Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

7 article(s) in your cart
pos.	image	product	Configure	Actions
1		ÜTA-32
2		EF 3…5 24 V
3		BK-380
4		ER-104
5		ZT-S
6		XR Relais
7		TSR-CAN-03

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

EF 3…5 24 V configure

1 Sicherheitsfunktion

2 Elektrodenanzahl

3 Anschlussgewinde

4 Stabmaterial

5 Stabdurchmesser

6 Beschichtung

7 Auswerteelektronik

8 Stablänge

9 SIL

Amount

additional infomation

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

ZT-S configure

1 Measuring End Range

2 Output signal

3 Connection

4 Process connection

Amount

additional infomation

XR Relais configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Versorgungsspannung

7 Busanschluss

8 SIL

9 ATEX

Amount

additional infomation

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties

connection : G 1” (andere Gewinde auf Anfrage)
max.length guide tube : siehe Diagramm
Operating temperature : atmosphär. Bedingungen
Operating pressure : atmosphär. Bedingungen
media density : siehe Eintauchtiefe
Number of contacts : beliebig
Contact load : max. 10 VA, max. 230 V AC
Length : max. 1750 mm

Material

Sight tube : PVC transparent
connection : PVC-Verschraubung mit PTFE-Stangenführung
Guide rod : Edelstahl, Titan, Hastelloy B, Hastelloy C oder PVCRohr
float : PE / PP

EF 3…5 24 V

Conductive electrodes with 24 V DC direct connection

The conductive electrodes EF3...5 are approved by the "DIBt" as overfill prevention devices for liquids hazardous to water.

Properties

connection : integrierter Anschlusskopf
Protection class : IP 65
connection thread : G 1¼"
Material Screw connection : PPH
Material electrode rods : Edelstahl (1.4571), Hastelloy C, Titan, Tantal
material coating : PTFE
Coating length : voll = ganzer Stab (10 mm am Stabende sind blank) teil = ca. 250 mm von oben
Rod diameter : 4 mm, 6 mm
rod length : max. 6 m
Operating temperature : 85 °C
Operating pressure : atmosphärisch
Spacer : ab Länge > 1000 mm je 1000 mm 1 Abstandshalter

Properties electronic part

Operating temperature : –20...+85 °C
Storage temperature : –30...+85 °C
nominal voltage : 24 V DC ± 15%
Power consumption : max. 2 W (Klemme A1, A2)
Switching voltage : max. 250 V AC, 150 V DC min. 5 V DC (Relais mit Kombi-Goldkontakten)
Switching current : max. 3 A AC, 3 A DC min. 1 mA
Switching capacity : max. 750 VA, 150 W
Sensitivity : 3k ... 100 kΩ in vier Stufen (3 k, 10 k, 30 k, 100 kΩ) wählbar

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

ER-104

1-channel electrode relay

Electrode relays for conductive level detection for all areas in which conductive, liquid media are to be detected, controlled or monitored

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
Storage temperature : –30...+80 °C
Weight : ca. 150g
ltdata. :

Power supply

nominal voltage : siehe Typenschlüssel
AC nominal frequency : 48...62 Hz
Power consumption : max. 1 W / VA

Input

Open circuit voltage : ≤ 10 V AC
Short-circuit current : ≤ 5 mA
Switching delay : siehe Typenschlüssel
Sensitivity range : siehe Typenschlüssel

Output

Contacts : potentialfreie Wechselkontakte
Switching voltage(min) : 5 V
Switching voltage (max) : 250 V AC / 150 V DC
Overvoltage category : EN 61010-1 Kategorie III

Switching current

Switching current : min. 5 mA
Switching current : max. cos φ =1 5 A
Switching current : max. cos φ = 0,7 3 A/AC
Switching current : max. cos φ = 1

ZT-S

Functionally safe pressure transmitter for ES series

Reliable pressure measurement and optimal process monitoring thanks to the ZT series. Developed for high demands and safety-critical applications

Properties

Operating voltage : 12...32 V DC (max. 0,2 W)
Dimensions : Ø 22 x 59 (D x H), SW22
Housing : Edelstahl
ltdata.MessbereichNenndruck : -1…500 bar
Overpressure : 2 x Nenndruck
Bursting pressure : 4 x Nenndruck
Protection class : IP65
Output signal : ZILA-DIO

Operating conditions

Pressure type : Relativdruck
Temperature of the fluid : -40 …+125 °C
ltdata.Medientemperatur(optional) : -20 …+125 °C
Ambient temperature : -40 …+105 °C

electrical connection

ltdata.Standard : Binder M12 x 1

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529