• Flag of Germany
  • Fluid.iO Webinar
  • Druckerzeuger sicher abschalten
  • (DO) 28.November 2024
  • 15:00–15:30 Uhr

T202

Immersible Magnetic Probe made of stainless steel (1.4571)

Features

product family

level measurement

product class

Point Level Measurement

suitable for

fluids

measurement principle

Magnet


Special characteristics

  • Independent of- Pressure, - Temperature, - Foam- Conductivity, - Dielectrics

  • Easy to install

  • High reproducibility & switching capacity

Description

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Technical Data

Properties
connection
Polyesterdose | Aluminiumdose
Protection class EN60529
IP 65 Anschlussdose
Connector plug
3- und 6-fach
connection thread
G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable
LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length
max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure
max. 20 bar
Viscosity
< 100 cp
Protection class EN60529
IP 68 Führungsrohr
Switching voltage
max. 250 V
Switching hysteresis
ca. 2...5 mm
Holding range
ca. 12 mm
Contact function
monostabil | bistabil
Operating temperature
ltdata.
max. +60...+150 °C
ltdata.
min. –20... –10 °C
ltdata.
höhere oder niedrigere Temperaturen auf Anfrage
Switching capacity
Changeover contact
60 W/VA
normally open
100 W/VA
Normally closed contact
60 W/VA
Switching current
Changeover contact
max. 1 A
NO/NC contact
max. 2 A
Contacts
Changeover contact
8
normally open
10
Normally closed contact
7

Further product information

T20X immersible magnetic probes are used for ascertaining the filling level limit values in tanks for liquid media. The materials used include PVC, PE, PPH, PTFE or stainless steel (1.4571), depending on requirements.

Through this the immersible magnetic probes are suitable for use with highly aggressive media. A ring magnet which switches the reed contacts built into the guide pipe is inserted into the float on the guide pipe. The switch contacts are hermetically sealed gas contacts which can be set up as changeover contacts or make or break contacts. With the E.L.B. limiting value magnet immersible probe it is possible to operate a number of switch contacts consecutively with one floater and, therefore, to measure a number of liquid levels. Monostable contacts are in-built as standard, i.e. the switch mode changes when the contact is operated by the magnet which is built into the floater. If the magnet goes above or below the contact, the contact will return to idle mode. If the contact is to be retained, an adjusting ring is required. If several levels are to be ascertained, several floats and adjusting rings are necessary. If required, bistable contacts are available, i.e. these contacts are operated and maintain this state until the contact is operated again. Please note! These contacts are shock-sensitive and therefore should not be used in the case of heavy turbulence.

Independent of

  • Pressure
  • Temperature
  • Foam
  • Conductivity
  • Dielectrics

Documents and Downloads

Accessoires

XR Relais

XR Relais

go to product

Similar Products

T200.F

T200.F

Overfill protection for containers

go to product

T-200.L

T-200.L

Leakage probes with general building authority approval

go to product

Benefit from our services

repair & maintenance

repair & maintenance

We produce durable products of high quality. However, if one of our products requires maintenance, we will gladly inspect the device in our Service Centre.

product development

product development

Our standard products have not yet completely convinced you? We offer customer-specific adaptation of our standard products to your wishes. Get in touch with us!

application-specific solution

application-specific solution

Are you looking for a suitable product solution for your measurement task? We recommend a product solution from our product range according to your specifications.

application-specific solution

Support & Start-up

Straightforward & fast support when things get stuck! Our support team will be glad to help you with any questions you may have about commissioning.

Our application engineers advise you personally, comprehensively and professionally!

Simply contact us by phone or e-mail!

Call us right away!

+49-6251-8462-0

contact form

Logo of Fluid.iO Sensor + Control

Fluid.iO
Sensor + Control
GmbH & Co. KG

An der Hartbrücke 6
64625 Bensheim
Tel.: +49-6251-8462-0
E-Mail: info@fluidio.de