Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

9 article(s) in your cart
pos.	image	product	Configure	Actions
1		HD-1XX
2		ER-107
3		TK-101 EX
4		QFS-40
5		T204-0.F
6		T205-0.F
7		ZDS-N
8		TK-101
9		MO

TK-101 EX configure

1 ATEX

Amount

additional infomation

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

TK-101 configure

1 ATEX

Amount

additional infomation

MO configure

1 Kontaktart

2 Kabelart

3 Kabellänge

4 Befestigung

Amount

additional infomation

HD-1XX

Hydrostatic filling level measurement

Continuous and precise level measurement in unpressurised, open basins and tanks as well as underground applications such as shafts, wells and boreholes.

ER-107

Electrode Relays with general approval for constructions Z-65.13-405, Z-65.40-191

Electrode relays for conductive level detection with approved design as part of an overfill cut-out device (Z-65.13-405) / leakage protection (Z-65.40-191)

Properties

details : folgen

TK-101 EX

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

T204-0.F

Immersible Magnetic Probe for Ex Zone 0 (Cat. 1)

The T20... magnetic immersion probes are used to detect fill level limits in containers for liquid media, where an explosive atmosphere of Zone 0 (Cat. 1) exists in the gas space above the liquid and an Ex-Zone 1 (Cat. 2) exists outside the container in the area of the junction box.

Properties

connection : Kabel PUR blau
Protection class : IP 68 Dose
number of floats : max. 4x
Operating temperature : max. 135 °C
F-Contact : 1 / 12 kΩ
Number of additional contacts : max. 3x Wechsler | 5x Schließer | 3x Öffner
Switching current : 1 A, 2 A (nur mit Schirmung)
Switching voltage : 230 V AC

Float

Stainless steel ball 61 mm Ø : max. 20 bar | 0,65 g/cm³
min. contact gap type 04 : 85 mm

Switching contacts and switching capacity

Changeover contact : max. 3x | 60W/VA
normally open : max. 5x | 100 W / VA
Normally closed contact : max. 3x | 60 W/VA

T205-0.F

Ex area zone 0 (category 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties