Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		TPS-210 TPS-220
2		BK-380
3		T20x.F
4		ÜTA-32
5		DS-CAN-01

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

T20x.F configure

1 Führungsrohr

2 Sicherheitsfunktion

3 Rohrmaterial

4 Anschlussgewinde

5 Ausführung

6 Schaltkontakte

7 Schwimmermaterial

8 Anschlussdose

9 Länge

Amount

additional infomation

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

TPS-210 TPS-220

Flexible, analogue dew point sensor

The dew point sensors of the enable direct measurement of the dew point and ambient temperature indoors and outdoors.

Properties TPS-210

Operating voltage : 12...30V DC
Power consumption : < 15mA

Properties TPS-220

Operating voltage : 24V DC
Loop voltage min: : Bürde(Ohm) *0,02 + 8 V
Loop voltage max: : 30V

General properties

Housing : Aluminium, eloxiert
Dimensions (in mm) : 135 x Ø 19,2

Measuring range

measuring range (Humidity) : 0…100% rH
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -50...+80°C
Measuring accuracy (temperature) : ± 0,2°C
Signal output : 0...10V | 4...20mA

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

T20x.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

Box : Polyester
Box : Aluminium
Box : Polyethylen
Box : Kabel
Box : Stecker

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating temperature : atmosphärisch; PP max. 90°C
Operating pressure : Max. 20 bar
media density : ρ ≥ 0,6 g/cm³ (je nach Schwimmertyp)
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Resistance value

Operational readiness : ca. 1 kΩ
overfill alarm : ca. 12 kΩ
Switching time : ca. 20 ms
ltdata. :

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties