Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

6 article(s) in your cart
pos.	image	product	Configure	Actions
1		T205-0.F
2		BK-390
3		TK-101 EX
4		T200.F-24V
5		T204
6		EP 24V

BK-390 configure

1 Rohr-Außendurchmesser

2 Kontakt

3 Stecker

Amount

additional infomation

TK-101 EX configure

1 ATEX

Amount

additional infomation

T200.F-24V configure

1 Führungsrohr

2 Sicherheitsfunktion

3 Rohrmaterial

4 Anschlussgewinde

5 Ausführung

6 Schwimmermaterial

7 Anschluss-Elektronikteil

Amount

additional infomation

EP 24V configure

1 Sondenkörpermaterial

2 Stabmaterial

3 Kabellänge

4 Leitungsüberwachungswiderstand

5 Kabelmaterial

6 Ex-Zulassung

Amount

additional infomation

T205-0.F

Ex area zone 0 (category 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties

Protection class : IP 68 Kabel
connection cable : max. 10 Meter PUR
Sliding tube length : Max. 6000 mm
Operating temperature : max. 120 °C
F-Contact : 1 / 12 kΩ

Float

Stainless steel ball 44 mm Ø : max. 15 bar | 0,60 g/cm³
Stainless steel cylinder 27 mm Ø : max. 10 bar | 0,78 g/cm³

BK-390

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

TK-101 EX

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

T200.F-24V

Overfill protection with 24V direct connection

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

ltdata.Polyesterdose : PO/ET-520
ltdata.Polyethylenanschlusskopf : PE/ET-521

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating temperature : max. 80 °C
Operating pressure : atmosphärisch
media density : ρ ≥ 0,6 g/cm³ (je nach Schwimmertyp)
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Power supply

nominal voltage : 24 V DC (24…300V DC)
Power consumption : ≤ 1 W

Output

Output contact : 1 potentialfreier Wechselkontakt
Switching voltage : max. 250 V AC / 30 V DC
Switching current : max. 3 A AC / 3 A DC
Switching capacity : max. 750 VA / 90 W

Optocoupler

Switching voltage : max. 30 V
Switching current : max. 100 mA
displays : Betriebs-LED grün, Funktions-LED rot
Switching delay : ca. 0,5 s Anzug/Abfall

T204

Magnetic immersion probe made of stainless steel (1.4571)

For use with highly aggressive liquid media to detect level limit values in containers. Suitable for use in hazardous areas, zone 0 (category 1).

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
connection thread : G1 1/2" | G2"
Sliding tube length : max. 6000 mm (Rohr Ø 12 mm)
Operating pressure : max. 20 bar (Kugel) | max. 15 bar (Zylinder)
Operating temperature : max. 135 °C
Number of floats : max. 4

Float type

Stainless steel ball 52mm ⌀ : Dichte: 0,75 g/cm³ | mind. Kontaktabstand: 75 mm
Stainless steel ball 62mm ⌀ : Dichte: 0,65 g/cm³ | mind. Kontaktabstand: 85 mm
Stainless steel cylinder 44 mm Ø : Dichte: 0,76 g/cm³ | mind. Kontaktabstand: 75 mm

Switching capacity