Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

6 article(s) in your cart
pos.	image	product	Configure	Actions
1		TK-312
2		T204
3		BK-3X0
4		T203.F
5		ZDS-N
6		T204.F

TK-312 configure

1 Housing

Amount

additional infomation

TK-312

Evaluation unit with 0/4... 20 mA current output

The TK-312 measuring transducer converts the resistance signal supplied from a continuous level sensor into a current signal proportionate to the level.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA, 2W
Dimensions housing type B : 22,5 x 114,5 x 99
Dimensions housing type C : 22,5 x 114,5 x 114

Input

Voltage : 0...10 V
Resistance in three-wire circuit RG : 0-4...10 kW

Output

Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Current output : 0/4... 20 mA bezogen auf die Masse des Eingangs
Voltage output : 0/2... 10 V
Mounting : Tragschiene nach EN 50022
Weight : 175 g

T204

Magnetic immersion probe made of stainless steel (1.4571)

For use with highly aggressive liquid media to detect level limit values in containers. Suitable for use in hazardous areas, zone 0 (category 1).

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
connection thread : G1 1/2" | G2"
Sliding tube length : max. 6000 mm (Rohr Ø 12 mm)
Operating pressure : max. 20 bar (Kugel) | max. 15 bar (Zylinder)
Operating temperature : max. 135 °C
Number of floats : max. 4

Float type

Stainless steel ball 52mm ⌀ : Dichte: 0,75 g/cm³ | mind. Kontaktabstand: 75 mm
Stainless steel ball 62mm ⌀ : Dichte: 0,65 g/cm³ | mind. Kontaktabstand: 85 mm
Stainless steel cylinder 44 mm Ø : Dichte: 0,76 g/cm³ | mind. Kontaktabstand: 75 mm

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 4
normally open : 6
Normally closed contact : 4

BK-3X0

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

T203.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Properties