Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

6 article(s) in your cart
pos.	image	product	Configure	Actions
1		T200.F-24V
2		BK-380
3		QFS-1X
4		ÜTA-32
5		ZDS-H
6		ZDT-H

T200.F-24V configure

1 Führungsrohr

2 Sicherheitsfunktion

3 Rohrmaterial

4 Anschlussgewinde

5 Ausführung

6 Schwimmermaterial

7 Anschluss-Elektronikteil

Amount

additional infomation

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

QFS-1X configure

1 Schwimmertyp

2 Kontakt

3 Schwimmermaterial

4 Kabelmaterial

5 TPK

6 Kabellänge

7 Ex

Amount

additional infomation

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

T200.F-24V

Overfill protection with 24V direct connection

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

ltdata.Polyesterdose : PO/ET-520
ltdata.Polyethylenanschlusskopf : PE/ET-521

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating temperature : max. 80 °C
Operating pressure : atmosphärisch
media density : ρ ≥ 0,6 g/cm³ (je nach Schwimmertyp)
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Power supply

nominal voltage : 24 V DC (24…300V DC)
Power consumption : ≤ 1 W

Output

Output contact : 1 potentialfreier Wechselkontakt
Switching voltage : max. 250 V AC / 30 V DC
Switching current : max. 3 A AC / 3 A DC
Switching capacity : max. 750 VA / 90 W

Optocoupler

Switching voltage : max. 30 V
Switching current : max. 100 mA
displays : Betriebs-LED grün, Funktions-LED rot
Switching delay : ca. 0,5 s Anzug/Abfall

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

QFS-1X

Float switch with reed switch (mercury-free)

Inside the float, one or two reed contacts with a movable permanent magnet are inserted as a switching element.

Properties

Protection class EN60529 : IP 68
Cable entry : PVC , PTFE
Conductor cross-section : 3 x 0,75 mm², PUR 3x0,5mm²
Switching system : Reed-Schalter
Contact : Wechsler, NO, NC (QFS-11 nur NO oder NC)
Switching voltage : 4...250 V AC/DC
Switching current : 1 mA ...1 A
Switching capacity : max. 1A, 60 VA/60 W
Switching hysteresis : ca. 100 mm
Switching angle : ca. + 20° / – 20°

Float

Material Float : PE (Polyethylen)
ltdata. :
ltdata. :
ltdata. :

Operating temperature

TPK(V), AEM : max. + 60 °C
PUR : max. + 70 °C
Silicone,Tefloncable with PE float : max. + 80 °C

Operating pressure

Cylinder : max. 1 bar
Sphere : max. 2 bar

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties