Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

7 article(s) in your cart
pos.	image	product	Configure	Actions
1		T205-0.F
2		TK-101 EX
3		QFS-40
4		BK-380
5		CS-11
6		ÜTA-32
7		DS-CAN-01

TK-101 EX configure

1 ATEX

Amount

additional infomation

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

T205-0.F

Ex area zone 0 (category 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties

Protection class : IP 68 Kabel
connection cable : max. 10 Meter PUR
Sliding tube length : Max. 6000 mm
Operating temperature : max. 120 °C
F-Contact : 1 / 12 kΩ

Float

Stainless steel ball 44 mm Ø : max. 15 bar | 0,60 g/cm³
Stainless steel cylinder 27 mm Ø : max. 10 bar | 0,78 g/cm³

TK-101 EX

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

CS-11

CO2 Sensor with digital Interface

Digital CO2 sensor CS-11 for measuring carbon dioxide concentration in mobile applications.

Properties CS-11

Measured variable: : CO2
Measuring range: : 0…5.000 ppm
Measuring principle: : optisch, NDIR
Housing : Kunststoff
measuring grid : 2 sec.
Accuracy : ± 50 ppm
Protocol : I²C-Bus
Operating conditions Temperature : -0°C … 50°C
Operating conditions Humidity : 0…85 % rH
Storage conditions Temperature : -30°C … 70 °C
Storage conditions Humidity : 0…85 % rH

Properties MV-CAN

Housing : Plastik
Mounting : Hutschienenmodul für Einbau in Schaltschrank
Operating voltage : 10…48 V
measuring grid : 2 sec.
CAN protocol : CANopen 2.0 A nach CiA DS 404
Physical Layer : nach ISO 11898
Option : Bereitstellung des EDS-Files
Operating temperature : -40°C … +80°C
Storage temperature : -40°C … +120 °C

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties