Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

7 article(s) in your cart
pos.	image	product	Configure	Actions
1		EF 3…5 24 V
2		ZMF-100-IR
3		TK-101 EX
4		QFS-40
5		FDL400
6		XR Relais
7		T205-0

EF 3…5 24 V configure

1 Sicherheitsfunktion

2 Elektrodenanzahl

3 Anschlussgewinde

4 Stabmaterial

5 Stabdurchmesser

6 Beschichtung

7 Auswerteelektronik

8 Stablänge

9 SIL

Amount

additional infomation

ZMF-100-IR configure

1 Output signal

2 Measuring range

Amount

additional infomation

TK-101 EX configure

1 ATEX

Amount

additional infomation

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

EF 3…5 24 V

Conductive electrodes with 24 V DC direct connection

The conductive electrodes EF3...5 are approved by the "DIBt" as overfill prevention devices for liquids hazardous to water.

Properties

connection : integrierter Anschlusskopf
Protection class : IP 65
connection thread : G 1¼"
Material Screw connection : PPH
Material electrode rods : Edelstahl (1.4571), Hastelloy C, Titan, Tantal
material coating : PTFE
Coating length : voll = ganzer Stab (10 mm am Stabende sind blank) teil = ca. 250 mm von oben
Rod diameter : 4 mm, 6 mm
rod length : max. 6 m
Operating temperature : 85 °C
Operating pressure : atmosphärisch
Spacer : ab Länge > 1000 mm je 1000 mm 1 Abstandshalter

Properties electronic part

Operating temperature : –20...+85 °C
Storage temperature : –30...+85 °C
nominal voltage : 24 V DC ± 15%
Power consumption : max. 2 W (Klemme A1, A2)
Switching voltage : max. 250 V AC, 150 V DC min. 5 V DC (Relais mit Kombi-Goldkontakten)
Switching current : max. 3 A AC, 3 A DC min. 1 mA
Switching capacity : max. 750 VA, 150 W
Sensitivity : 3k ... 100 kΩ in vier Stufen (3 k, 10 k, 30 k, 100 kΩ) wählbar

ZMF-100-IR

gas detector with 4...20mA signal output

industrial CO2 sensor ZMF-100-IR with a measuring range of up to 50,000ppm

Product features

Measuring principle : optisch, NDIR (nicht-dispersive Infrarot-Absorptionsmessung)
Operating voltage : 24 V DC / 100 mA
Heating time : ca. 5 min
Response time : ca. 30 s
Repeatability : +/- 1%
Housing : Aluminium (rot) IP54
Weight : ca. 500g
Shaft range : 4,27 - 4,35 µm (4270-4350 nm)
Gas ingress : per Diffusion

ambient conditions

Operating temperature range : -10...+50 °C
Storage temperature range : -40...+100 °C
RelativeHumidity : 15..95 %
Air pressure : 900...1100 hPa

TK-101 EX

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

FDL400

Flow Data Logger

The FDL400 "Flow Data Logger 400" measuring device is suitable for measuring the flow of water and wastewater in fully or partially filled sewers or pipes of various geometries.

Properties

Housing : Aluminium
Protection class : IP30
Dimensions : 197 x 153 x 37,5mm (B x H x T)
Temperature range : 0 – 50°C
Supply voltage : 24V DC +/-20%
Power consumption : 120mA – 220mA
Reverse polarity protection : ✓
Display : 4x20

Outputs

analog 0(4)–20mA : 3x
digital : 4x
fixed for alarm : 1x
free configurable : 3x

display of measured value

Flow velocity :
Filling level :
flow :
flow rate :

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529