Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

6 article(s) in your cart
pos.	image	product	Configure	Actions
1		T200.F
2		BK-380
3		TK-313
4		TRM-100
5		NP-256
6		T-200.L

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

TK-313 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

TRM-100 configure

1 Material

2 Measuringrange

3 Connection

4 Flange

5 Sealing

Amount

additional infomation

NP-256 configure

1 Ausführung

2 Staurohr-Anzahl

3 Anschlussgewinde

4 Druckschalter

5 Kontakt

6 Längen

Amount

additional infomation

T200.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

ltdata.Polyesterdose :
ltdata.Aluminiumdose :
ltdata.Polyethylenanschlusskopf :
Cable :
Plug :

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating pressure : Max. 20 bar
media density : ρ ≥ 0,6 g/cm³
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm
Operating temperature : atmosphärisch
ltdata.BetriebstemperaturPP : max. 90°C

Resistance value

Operational readiness : ca. 1 kΩ
overfill alarm : ca. 12 kΩ
Switching time : ca. 20 ms
ltdata. :

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

TK-313

Evaluation unit with 2 change over limit contacts

The TK-313 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control / measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99
Dimensions housing type C : 22,5 x 114,5 x 114

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 2 Wechselkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g
ltdata. :

TRM-100

Turbidimeter (0...1.000 FNU or 500...4.000 FAU)

The turbidimeter TRM-100 is a compact device for measuring turbidity in liquids. The "turbidity" is measured using the scattered light method (angle 90 degrees) for the turbidity range of < 1,000 FNU (Formazine Nephelometric Units) and the transmitted light method (angle 0 degrees) for the turbidity ranges > 1,000 FAU (Formazine Attenuation Units).

Properties

Operating pressure : max. 10 bar @ 20 °C | max. 2,5 bar @ 60 °C
Measuring range : 500...4.000 FNU / FAU
Measuring accuracy : +/-5 %
Mounting position : horizontal
Process connection : DN 20 | DN 40
Flange connection : >= DN 20
number of senders : 2
number of receivers : 1

Material

Seal : EPDM | optional FPM (Viton)
Process connection : PVC | PPH
Measuring tube : Borsilikatglas mit Nano Beschichtung

Input

Power supply : 18...30 V DC
Power consumption : < 2 W

Output

Output contact : 4...20 mA
Switching delay (adjustable) : 1...10 s
Protection class : IP 65
Switching voltage : max. 250 V AC | max. 115 V DC
Switching current : max. 3 A
Switching capacity : max. 500 VA, 60 Watt
Potential-free changeover contact : 1 @ 1...10 s

NP-256

Level Switch - multiple 2...4 - pneumatic (hose)

very reliable and simple sensors for scanning liquids, in particular when used for overflow protection. liquids can be aggressive, sticky or highly contaminated

Properties