Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

10 article(s) in your cart
pos.	image	product	Configure	Actions
1		T203.F
2		ELH
3		TK-315
4		TSR-CAN-03
5		QFS-55
6		TSL-CAN-03
7		ZMF-100-IR
8		BK-390
9		OAA-300
10		T205-0.F

TK-315 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

QFS-55 configure

1 Ausführung

2 Kontakt

3 Schaltkontakt

4 Kabelmaterial

5 Kabellänge

6 Ex-Option

Amount

additional infomation

ZMF-100-IR configure

1 Output signal

2 Measuring range

Amount

additional infomation

BK-390 configure

1 Rohr-Außendurchmesser

2 Kontakt

3 Stecker

Amount

additional infomation

OAA-300 configure

1 Ausführung

2 Versorgungsspannung

3 Signalgeber

Amount

additional infomation

T203.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Properties

Protection class : IP 65 Dose
Sliding tube length : max. 6000 mm
Operating temperature : max. 135 °C
Operating pressure : max. 20 bar
F-Contact : 1/12 kΩ
Switching current : 1A, 2A
Switching voltage : 230 V AC

Float

quantity : max. 6
Type 05 : Oval Edelstahl 76 mm Ø | Dichte 0,81 g/cm³
Type 06 : Oval Edelstahl 90 mm Ø | Dichte 0,67 g/cm³
Minimum contact distance : Typ 05: 110 mm | Typ 06: 135 mm

Switching contacts and switching capacity

Changeover contact : max. 5x | 60 W/VA
normally open : max. 6x | 100 W/VA
Normally closed contact : max. 4x | 60 W/VA

ELH

Suspension electrode as leakage probe

The leakage probes of the type series ELH are approved by the "DIBt" for the monitoring of collecting chambers, collecting devices, inspection and filling shafts.

General data

Protection class : IP 68
Probe body material : PE, PVC, PPH, PVDF
Diameter probe body : 15 mm, 25 mm, 40 mm
Operating temperature : atmosphärisch
Operating pressure : atmosphärisch
Resistance value of line monitoring : 22 kΩ / 100 kΩ

Material

Screw connection : PVDF
Cable : TPK ( PVC Basis)
on request : FEP (Teflon), PVC - blau
cable length : auf Wunsch (Standard 3 m)
Material Sensor rods : Edelstahl (1.4571), Hastelloy B, Hastelloy C, Titan, Tantal, Glas-Kohlestifte

TK-315

Evaluation unit with 4 limit contacts (NO-contacts)

The TK-315 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control/measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99 mm
Dimensions housing type C : 22,5 x 114,5 x 114 mm

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 4 Schließerkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g

TSR-CAN-03

CANopen transmitter for temperature measurement in media

High-quality stainless steel transmitter for precise temperature measurement in all stainless steel-compatible media

Measurement parameters

Measuring range : -40…+80 °C (optional +150°C)
deviation : ± 0,3 K (-40…+80 °C)
Measuring element : Halbleiter
measuring resolution : 10 Bit
measuring grid : ab 5 ms

ElectricalConnection

CAN protocol : CANopen 2.0 A, nach ciA DS 404
Physical Layer : nach DIN 11898
Operating voltage : 12…27 V ±20 %

Operating conditions

Operating temperature : -40...+80 °C
Storage temperature : -40°C...+120°C
Shock resistance : 30g, Dauer: 14 ms bei Raumtemperatur
Vibration resistance : 10g bei 20 bis 1000 Hz

QFS-55

Teflon float switch in rod design

The float switch combination is built with float switches of the QFS-50 and QFS-60 series. This makes it possible to control a level in a simple way.

Technical Data

Material : PTFE (Teflon)
connection cable : Silikon, Teflon
Material rod : VA-Rohr, PTFE beschichtet
Operating temperature : max. +150 °C
media density : ρ ≥ 0,75 g/cm³
Switching system : Reed-Schalter
Contact : Wechsler, NO, NC
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
Ex-protection optional : Elektrische Daten siehe EG-Prüfbescheinigung IBExU10ATEX 1089

Reed contact

Switching current : 1 mA ... 1 A
Switching voltage : 24 ... 250 V AC/DC
Switching capacity : Max. 1A, 60 VA / 60 W
Switching hysteresis : ca. 100 mm
Switching angle : ca. +20°...–20°

Namur circuit (1kΩ/12kQ)

Switching current / switching voltage : nur zum Anschluss an KR-163... oder andere „Namur”-Relais
Switching hysteresis : ca. 100 mm
Switching angle : ca. +20°...–20°

TSL-CAN-03

Temperature sensor with CAN bus interface for air temperature measurement

CANopen transmitter for temperature measurement in media, semiconductor sensor

Properties

Measuring range : -40…+80 °C
deviation : ± 0,3 K (10...80 °C)
Measuring element : Halbleiter-Diodenfühler
measuring resolution : 0,1 K
measuring grid : ab 5 ms

ElectricalConnection

CAN protocol : CANopen 2.0 A, nach ciA DS 404
Physical Layer : nach DIN 11898
Operating voltage : 10...48 V

Operating conditions

Operating temperature : -40...+80 °C
Storage temperature : -40°C...+120°C
Shock resistance : 30g, Dauer: 14 ms bei Raumtemperatur
Vibration resistance : 10g bei 20 bis 1000 Hz
Minimumairspeedrequiredformeasurementacrossthesensor : 1,5 m/s

ZMF-100-IR

gas detector with 4...20mA signal output

industrial CO2 sensor ZMF-100-IR with a measuring range of up to 50,000ppm

Product features

Measuring principle : optisch, NDIR (nicht-dispersive Infrarot-Absorptionsmessung)
Operating voltage : 24 V DC / 100 mA
Heating time : ca. 5 min
Response time : ca. 30 s
Repeatability : +/- 1%
Housing : Aluminium (rot) IP54
Weight : ca. 500g
Shaft range : 4,27 - 4,35 µm (4270-4350 nm)
Gas ingress : per Diffusion

ambient conditions

Operating temperature range : -10...+50 °C
Storage temperature range : -40...+100 °C
RelativeHumidity : 15..95 %
Air pressure : 900...1100 hPa

BK-390

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

OAA-300

Alarm Indicator (Measuring Transducer) with general approval for construction

Our alarm indicators type OAA-300 are stand-alone signaling devices with optic and acoustic alarm indication.

Properties

Protection class EN60529 : IP 65
Operating temperature : – 20…+60 °C
Storage temperature : – 30…+80 °C
Sensitivity : bei konduktiver Messung: 3, 10, 30, 100kΩ
Dimensions : 170 x 190 x 85 mm
Weight : ca. 0,8 kg

Control circuits

Open circuit voltage : max. 10 V DC
Short-circuit current : max. 10 mA
Switching delay : ca. 0,5 s

Power supply

nominal voltage : 230 V AC (optional 24, 115, 240 V AC 24 V DC
Nominal frequency : 48...62 Hz
Power consumption : max. 3 W/VA

Output

Switching voltage : max. 250 V
Switching current : max. 3 A
Switching capacity : max. 500 VA | max. 50 W
Volume : 75 dB

T205-0.F

Ex area zone 0 (category 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties