Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		TPS-210 TPS-220
2		QFS-40
3		T209-0.F
4		T-200.L
5		T203.F

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

T-200.L configure

1 Länge

2 Anschluss

3 Anschlussgewinde

4 Befestigungswinkel

5 Schwimmertyp

Amount

additional infomation

TPS-210 TPS-220

Flexible, analogue dew point sensor

The dew point sensors of the enable direct measurement of the dew point and ambient temperature indoors and outdoors.

Properties TPS-210

Operating voltage : 12...30V DC
Power consumption : < 15mA

Properties TPS-220

Operating voltage : 24V DC
Loop voltage min: : Bürde(Ohm) *0,02 + 8 V
Loop voltage max: : 30V

General properties

Housing : Aluminium, eloxiert
Dimensions (in mm) : 135 x Ø 19,2

Measuring range

measuring range (Humidity) : 0…100% rH
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -50...+80°C
Measuring accuracy (temperature) : ± 0,2°C
Signal output : 0...10V | 4...20mA

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

T209-0.F

Magnetic immersion probe overfill protection for Ex zone 0 (Cat. 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties

connection : Polyesterdose, Aluminiumdose
Protection class : IP 65 Dose
Float type : Kugel Edelstahl 105 mm Ø
Sliding tube length : max. 6000 mm
Operating temperature : max. 135°C
Operating pressure : max. 20 bar
media density : 0,54 g/cm³
F-Contact : 1 / 12 kΩ
Number of additional contacts : 6x Wechsler, 9x Schließer, 6x Öffner
Switching current : 1A, 2A ( nur mit Schirmung)
Switching capacity : Wechsler: 60 W/VA, Schließer: 100 W/VA Öffner: 60 W/VA
min. contact distance with several floats : 125 mm

T-200.L

Leakage probes with general building authority approval

The leakage probes T-200.L are approved by the "DIBt" on the basis of the "WasBauPVO" for the detection of leaked liquids hazardous to water.

Connection

Box : Polyesterdose (PO)
Box : Polyethylen-Anschlusskopf (PE)
Cable : Kabel (TPK)
Plug : Stecker (ST)

Properties

Protection class : IP 65
Cable entry : PVDF-Verschraubung , PVC-Dichtung
Material Float : PE
Material leakage probe base : PE
Cable : TPK (PVC Basis)
Operating temperature : atmosphärisch
Operating pressure : atmosphärisch
media density : mit Schwimmer PE 52 ρ ≥ 1,05 g/cm³
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Resistance value

Operational readiness : ca. 1 kΩ
Leakage detection : ca. 12 kΩ

T203.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Properties