Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		QFS-40
2		T205-0.F
3		T-200.L
4		HD-110 \| HD-112 \| HD-114
5		T209

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

T-200.L configure

1 Länge

2 Anschluss

3 Anschlussgewinde

4 Befestigungswinkel

5 Schwimmertyp

Amount

additional infomation

HD-110 | HD-112 | HD-114 configure

1 Gehäuse

2 Anschlussgewinde

3 Messbereich

4 Ausgangssignal

5 Steckverbindung

6 Abdichtung

7 Sondermesszelle

Amount

additional infomation

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

T205-0.F

Ex area zone 0 (category 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties

Protection class : IP 68 Kabel
connection cable : max. 10 Meter PUR
Sliding tube length : Max. 6000 mm
Operating temperature : max. 120 °C
F-Contact : 1 / 12 kΩ

Float

Stainless steel ball 44 mm Ø : max. 15 bar | 0,60 g/cm³
Stainless steel cylinder 27 mm Ø : max. 10 bar | 0,78 g/cm³

T-200.L

Leakage probes with general building authority approval

The leakage probes T-200.L are approved by the "DIBt" on the basis of the "WasBauPVO" for the detection of leaked liquids hazardous to water.

Connection

Box : Polyesterdose (PO)
Box : Polyethylen-Anschlusskopf (PE)
Cable : Kabel (TPK)
Plug : Stecker (ST)

Properties

Protection class : IP 65
Cable entry : PVDF-Verschraubung , PVC-Dichtung
Material Float : PE
Material leakage probe base : PE
Cable : TPK (PVC Basis)
Operating temperature : atmosphärisch
Operating pressure : atmosphärisch
media density : mit Schwimmer PE 52 ρ ≥ 1,05 g/cm³
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Resistance value

Operational readiness : ca. 1 kΩ
Leakage detection : ca. 12 kΩ

HD-110 | HD-112 | HD-114

Hydrostatic screw-in probes (4...20mA | 0.8...10mWS)

Continuous and precise level measurement in unpressurised, open basins and tanks as well as underground applications such as shafts, wells and boreholes.

Properties

Protection class EN60529 : IP 65
Operating temperature : -10...70 °C
Storage temperature : -25...70 °C
Power supply : 15...30 V DC
power : max. 25 mA
Output : 2-Leiter-Technik | 4...20 mA
Measuring range : 0,8...10 mWs (Standard)
Overpressure : ca. 20 %
Deviation from characteristic curve : Nichtlinearität,
Insulation resistance : > 100 kΩ
Short-circuit resistance : permanent
Reverse polarity protection : keine Schädigung o. Funktion bei vertauschten Anschlüssen

Materials

Housing : Edelstahl 1.4571, PVC, PVDF
Measuring cell : Edelstahl 1.4404, Keramik AI2o3 96%, Keramik AI2o3 99,9%
Seals : FKM (Viton ®), EPDM, FFKM (Kalrez ®)
connection thread : G ¾“ | G 1 ½“
Plug : Steckverbindung DIN 43650

T209

Immersible Magnetic Probe made of PVC, PE, PPH, PTFE or stainless steel (1.4571)

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil