Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

6 article(s) in your cart
pos.	image	product	Configure	Actions
1		T-200.L
2		ZMF-100-IR
3		T200.F
4		TPS-410 TPS-420
5		T202
6		XR-4x0 \| XR-4x1

ZMF-100-IR configure

1 Output signal

2 Measuring range

Amount

additional infomation

XR-4x0 | XR-4x1 configure

1 Kanalanzahl

2 Option

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Empfindlichkeitsbereich

7 Versorgungsspannung

8 Busanschluss

9 SIL

10 Ex

Amount

additional infomation

T-200.L

Leakage probes with general building authority approval

The leakage probes T-200.L are approved by the "DIBt" on the basis of the "WasBauPVO" for the detection of leaked liquids hazardous to water.

ZMF-100-IR

gas detector with 4...20mA signal output

industrial CO2 sensor ZMF-100-IR with a measuring range of up to 50,000ppm

Product features

Measuring principle : optisch, NDIR (nicht-dispersive Infrarot-Absorptionsmessung)
Operating voltage : 24 V DC / 100 mA
Heating time : ca. 5 min
Response time : ca. 30 s
Repeatability : +/- 1%
Housing : Aluminium (rot) IP54
Weight : ca. 500g
Shaft range : 4,27 - 4,35 µm (4270-4350 nm)
Gas ingress : per Diffusion

ambient conditions

Operating temperature range : -10...+50 °C
Storage temperature range : -40...+100 °C
RelativeHumidity : 15..95 %
Air pressure : 900...1100 hPa

T200.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

ltdata.Polyesterdose :
ltdata.Aluminiumdose :
ltdata.Polyethylenanschlusskopf :
Cable :
Plug :

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating pressure : Max. 20 bar
media density : ρ ≥ 0,6 g/cm³
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm
Operating temperature : atmosphärisch
ltdata.BetriebstemperaturPP : max. 90°C

Resistance value

Operational readiness : ca. 1 kΩ
overfill alarm : ca. 12 kΩ
Switching time : ca. 20 ms
ltdata. :

TPS-410 TPS-420

Compact, analogue dew point sensor

The dew point sensors of the enable direct measurement of the dew point and ambient temperature indoors and outdoors.

Properties TPS-410

Operating voltage : 12...30V DC
Power consumption : < 15mA
Protection class : Gehäuse IP66, Stecker IP 67
Weight : 96g

Properties TPS-420

Operating voltage : 24V DC
Loop voltage min: : Bürde(Ohm) *0,02 + 8 V
Loop voltage max: : 30V

General properties

Housing : Aluminium, eloxiert
Dimensions (in mm) : 135 x Ø 19,2

Measuring range

measuring range (dew point) : -50…+80 °C
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -40...+80°C
Measuring accuracy (temperature) : ± 0,2°C
Signal output : 0...10V | 4...20mA

T202

Immersible Magnetic Probe made of stainless steel (1.4571)

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil

Operating temperature

ltdata. : max. +60...+150 °C
ltdata. : min. –20... –10 °C
ltdata. : höhere oder niedrigere Temperaturen auf Anfrage

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 8
normally open : 10
Normally closed contact : 7

XR-4x0 | XR-4x1

Electrode relay with ATEX

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised.

Protection class EN60529