Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		TK-315
2		BK-3X0
3		T200.F-24V
4		KS-210 KS-220
5		XR Relais

TK-315 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

T200.F-24V configure

1 Führungsrohr

2 Sicherheitsfunktion

3 Rohrmaterial

4 Anschlussgewinde

5 Ausführung

6 Schwimmermaterial

7 Anschluss-Elektronikteil

Amount

additional infomation

TK-315

Evaluation unit with 4 limit contacts (NO-contacts)

The TK-315 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control/measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99 mm
Dimensions housing type C : 22,5 x 114,5 x 114 mm

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 4 Schließerkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g

BK-3X0

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

T200.F-24V

Overfill protection with 24V direct connection

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

ltdata.Polyesterdose : PO/ET-520
ltdata.Polyethylenanschlusskopf : PE/ET-521

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating temperature : max. 80 °C
Operating pressure : atmosphärisch
media density : ρ ≥ 0,6 g/cm³ (je nach Schwimmertyp)
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Power supply

nominal voltage : 24 V DC (24…300V DC)
Power consumption : ≤ 1 W

Output

Output contact : 1 potentialfreier Wechselkontakt
Switching voltage : max. 250 V AC / 30 V DC
Switching current : max. 3 A AC / 3 A DC
Switching capacity : max. 750 VA / 90 W

Optocoupler

Switching voltage : max. 30 V
Switching current : max. 100 mA
displays : Betriebs-LED grün, Funktions-LED rot
Switching delay : ca. 0,5 s Anzug/Abfall

KS-210 KS-220

Compact sensors for temperature & humidity measurement

The KS series sensors are modular temperature and humidity measurement sensors in compact housings for use in almost any application.

Properties KS-210

Operating voltage : 12...30V DC
Power consumption : < 15mA

Properties KS-220

Operating voltage : 24V DC
Loop voltage min: : Bürde(Ohm) *0,02 + 8 V
Loop voltage max: : 30V

General properties

Housing : Aluminium, eloxiert
Dimensions (in mm) : 135 x Ø 19,2

Measuring range

measuring range (Humidity) : 0…10% rH
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -40...+80°C
Measuring accuracy (temperature) : ± 0,2°C
Signal output : 0...10V | 4...20mA

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529