Home
Cart

Cart

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

8 article(s) in your cart
pos.	image	product	Configure	Actions
1		ELH
2		QFS-40
3		Ex-BK
4		XR Relais
5		Lub-VDT USB-Kit
6		ViscoScope® VA-300
7		TK-301
8		T206

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

Ex-BK configure

1 Ex

Amount

additional infomation

XR Relais configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Versorgungsspannung

7 Busanschluss

8 SIL

9 ATEX

Amount

additional infomation

ViscoScope® VA-300 configure

1 Viscosity

2 Temperature

3 Process-Connection

4 Material

5 Non-active-Extension

6 Ex-Bereich

Amount

additional infomation

TK-301 configure

1 Material Rohr und Verschraubung

2 Gewinde

3 Ausführung

4 Schwimmerausführung

5 Anschluss

6 Rohrlänge

7 Auflösung

8 Zubehör

Amount

additional infomation

ELH

Suspension electrode as leakage probe

The leakage probes of the type series ELH are approved by the "DIBt" for the monitoring of collecting chambers, collecting devices, inspection and filling shafts.

General data

Protection class : IP 68
Probe body material : PE, PVC, PPH, PVDF
Diameter probe body : 15 mm, 25 mm, 40 mm
Operating temperature : atmosphärisch
Operating pressure : atmosphärisch
Resistance value of line monitoring : 22 kΩ / 100 kΩ

Material

Screw connection : PVDF
Cable : TPK ( PVC Basis)
on request : FEP (Teflon), PVC - blau
cable length : auf Wunsch (Standard 3 m)
Material Sensor rods : Edelstahl (1.4571), Hastelloy B, Hastelloy C, Titan, Tantal, Glas-Kohlestifte

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

Ex-BK

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –20...+120 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm
Dimensions : 80 mm x 75 mm x 57 mm

Material

Housing : Aluminium
Mounting clip : V2A
Rivet : V2A
Screw connection : M 20 x 1.5, V2A

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 24...250 V AC/DC
Switching current : 20 mA...6 A AC/DC
Switching capacity(min.) : max. 500 VA, 60 W
Switching capacity(max.) : min. 2 VA/W

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529