Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

6 article(s) in your cart
pos.	image	product	Configure	Actions
1		T204-0
2		Ex-BK
3		TK-312
4		KS-Serie
5		T200.F-24V
6		XR Relais

Ex-BK configure

1 Ex

Amount

additional infomation

TK-312 configure

1 Housing

Amount

additional infomation

T200.F-24V configure

1 Führungsrohr

2 Sicherheitsfunktion

3 Rohrmaterial

4 Anschlussgewinde

5 Ausführung

6 Schwimmermaterial

7 Anschluss-Elektronikteil

Amount

additional infomation

XR Relais configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Versorgungsspannung

7 Busanschluss

8 SIL

9 ATEX

Amount

additional infomation

T204-0

Magnetic immersion probe made of stainless steel (1.4571) as a cable tail variant

For use with highly aggressive liquid media to detect level limit values in containers. Suitable for use in hazardous areas, zone 0 (category 1).

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil

Operating temperature

ltdata. : max. +60...+150 °C
ltdata. : min. –20... –10 °C
ltdata. : höhere oder niedrigere Temperaturen auf Anfrage

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 8
normally open : 10
Normally closed contact : 7

Ex-BK

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –20...+120 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm
Dimensions : 80 mm x 75 mm x 57 mm

Material

Housing : Aluminium
Mounting clip : V2A
Rivet : V2A
Screw connection : M 20 x 1.5, V2A

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 24...250 V AC/DC
Switching current : 20 mA...6 A AC/DC
Switching capacity(min.) : max. 500 VA, 60 W
Switching capacity(max.) : min. 2 VA/W

TK-312

Evaluation unit with 0/4... 20 mA current output

The TK-312 measuring transducer converts the resistance signal supplied from a continuous level sensor into a current signal proportionate to the level.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA, 2W
Dimensions housing type B : 22,5 x 114,5 x 99
Dimensions housing type C : 22,5 x 114,5 x 114

Input

Voltage : 0...10 V
Resistance in three-wire circuit RG : 0-4...10 kW

Output

Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Current output : 0/4... 20 mA bezogen auf die Masse des Eingangs
Voltage output : 0/2... 10 V
Mounting : Tragschiene nach EN 50022
Weight : 175 g

KS-Serie

Sensors for temperature & humidity measurement

The KS series sensors are modular temperature and humidity measurement sensors in compact housings for use in almost any application.

Specifications

Housing shapes : Stabform | Alu- oder Polycarbonatgehäuse
measurands : Temperatur | relative Feuchte
Measuring range : -40...+80 °C | 0...100% rH
Signal output : 0...10 V oder 4…20 mA
Power supply : 12...30 V DC | 24 V DC

T200.F-24V

Overfill protection with 24V direct connection

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

ltdata.Polyesterdose : PO/ET-520
ltdata.Polyethylenanschlusskopf : PE/ET-521

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating temperature : max. 80 °C
Operating pressure : atmosphärisch
media density : ρ ≥ 0,6 g/cm³ (je nach Schwimmertyp)
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Power supply

nominal voltage : 24 V DC (24…300V DC)
Power consumption : ≤ 1 W

Output

Output contact : 1 potentialfreier Wechselkontakt
Switching voltage : max. 250 V AC / 30 V DC
Switching current : max. 3 A AC / 3 A DC
Switching capacity : max. 750 VA / 90 W

Optocoupler

Switching voltage : max. 30 V
Switching current : max. 100 mA
displays : Betriebs-LED grün, Funktions-LED rot
Switching delay : ca. 0,5 s Anzug/Abfall

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529