Home
Cart

Cart

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

4 article(s) in your cart
pos.	image	product	Configure	Actions
1		BK-380
2		Fluidix Lub-VDT
3		T200
4		T205-0.F

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

Fluidix Lub-VDT configure

1 Signalausgang

2 Messbereich

Amount

additional infomation

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

Fluidix Lub-VDT

Oil condition sensor for permanent monitoring of mechanical properties of liquids

The FluidIX Lub-VDT enables inline monitoring of mechanical fluid properties.

Properties

CE marking : EN 61000-6-1/2/3/4
Operating voltage : 9...32 V DC
Housing material : Edelstahl
Protection class : IP 67
Dimensions : 30x90 mm
Process connection : G 3/8"
Electrical connection : M12-8 A-Coding
Weight : 150g
Measurement output : 2x 4...20mA
bus protocol : ModbusRTU, CANopen

Measured variables

Resonator frequency : 20...25 kHz
Viscosity : 1-650 cSt (mm²/s)
density : 0.5-1.5 g/cm³
Temperature : -40...+125°C
sampling rate : 1/s

Operating conditions

Temperature of the fluid : -40...+125°C
Housing temperature : -40...+100°C
oil pressure : Max. 50 bar*
particle size : 250 μm
*higher pressure on request :

T200

Immersible Magnetic Probe made of PVC, PE, PPH, PTFE or stainless steel (1.4571)

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil

Operating temperature

ltdata. : max. +60...+150 °C
ltdata. : min. –20... –10 °C
ltdata. : höhere oder niedrigere Temperaturen auf Anfrage

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 8
normally open : 10
Normally closed contact : 7

T205-0.F

Ex area zone 0 (category 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties