Home
Cart

Cart

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

10 article(s) in your cart
pos.	image	product	Configure	Actions
1		ZDS-N
2		T204
3		CS-11
4		XR Relais
5		TK-101 EX
6		KS-Serie
7		KST-20 Calima
8		cIO CANopen Module
9		T202
10		KS-CAN-03

TK-101 EX configure

1 ATEX

Amount

additional infomation

KST-20 Calima configure

1 Innensensor

2 Außensensor

Amount

additional infomation

KS-CAN-03 configure

1 Protectice Cap

Amount

additional infomation

ZDS-N

Precision pressure switch for low pressure applications

Can be used in oil, brake fluid, diesel, air and other gases. With very good stability and overpressure resistance.

technical properties

Pressure range : 0...500mbar gestuft
supply : 12 - 24 V DC
Output : Relais 230 V/1A
overload : 2 x Messbereich
Med. connection : Schlauch
electrical connection : Schraubklemme
feature : Tasten, LCD-Anz.

T204

Magnetic immersion probe made of stainless steel (1.4571)

For use with highly aggressive liquid media to detect level limit values in containers. Suitable for use in hazardous areas, zone 0 (category 1).

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
connection thread : G1 1/2" | G2"
Sliding tube length : max. 6000 mm (Rohr Ø 12 mm)
Operating pressure : max. 20 bar (Kugel) | max. 15 bar (Zylinder)
Operating temperature : max. 135 °C
Number of floats : max. 4

Float type

Stainless steel ball 52mm ⌀ : Dichte: 0,75 g/cm³ | mind. Kontaktabstand: 75 mm
Stainless steel ball 62mm ⌀ : Dichte: 0,65 g/cm³ | mind. Kontaktabstand: 85 mm
Stainless steel cylinder 44 mm Ø : Dichte: 0,76 g/cm³ | mind. Kontaktabstand: 75 mm

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 4
normally open : 6
Normally closed contact : 4

CS-11

CO2 Sensor with digital Interface

Digital CO2 sensor CS-11 for measuring carbon dioxide concentration in mobile applications.

Properties CS-11

Measured variable: : CO2
Measuring range: : 0…5.000 ppm
Measuring principle: : optisch, NDIR
Housing : Kunststoff
measuring grid : 2 sec.
Accuracy : ± 50 ppm
Protocol : I²C-Bus
Operating conditions Temperature : -0°C … 50°C
Operating conditions Humidity : 0…85 % rH
Storage conditions Temperature : -30°C … 70 °C
Storage conditions Humidity : 0…85 % rH

Properties MV-CAN

Housing : Plastik
Mounting : Hutschienenmodul für Einbau in Schaltschrank
Operating voltage : 10…48 V
measuring grid : 2 sec.
CAN protocol : CANopen 2.0 A nach CiA DS 404
Physical Layer : nach ISO 11898
Option : Bereitstellung des EDS-Files
Operating temperature : -40°C … +80°C
Storage temperature : -40°C … +120 °C

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529

clamp : IP20
Housing : IP40

Technical Data

Operating temperature : -20...+60 °C
Storage temperature : -30...+80 °C
Output contacts : potentialfrei
Switching voltage : min. 5 V | max. 250 V AC / 150 V DC
Switching current : min. 5 mA | max. 5 A AC / 5 A DC
Switching capacity : min. 300 mW | max. 100 VA / 50 W
Quiescent current : umschaltbar
Weight : ca. 250 g
CE marking : siehe Konformitätserklärung
Ex-protection/IECEx : siehe Prüfbescheinigung

TK-101 EX

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

KS-Serie

Sensors for temperature & humidity measurement

The KS series sensors are modular temperature and humidity measurement sensors in compact housings for use in almost any application.

Specifications

Housing shapes : Stabform | Alu- oder Polycarbonatgehäuse
measurands : Temperatur | relative Feuchte
Measuring range : -40...+80 °C | 0...100% rH
Signal output : 0...10 V oder 4…20 mA
Power supply : 12...30 V DC | 24 V DC

KST-20 Calima

Climate control for automatic & controlled dehumidification, ventilation and cooling of rooms

The KST-20 Calima climate control system with aH-Controlled technology for ventilation and dehumidification for all types of private, commercial and industrial rooms. With the operating modes for living room ventilation and room dehumidification, the KST-20 Calima can be used flexibly in almost all living, working and industrial areas.

Specifications

measuring range (Humidity) : 0…100% rF,
Measuring accuracy (humidity) : ±2%
measuring range (Temperature) : -40…+80°C
Measuring accuracy (temperature) : ±0,2°C
Signal output : I2C
Connections for actuators : Zwei Steuer- und Schaltausgänge für Zuluft- und Abluftelemente
Power supply : 230 V AC
Protection class : IP 65
Dimensions (LxBxH) : 140x140x46 mm

Connection options

Dehumidification : Einstufige Lüftungsventilatoren
Room dehumidification / living space ventilation : Zweistufige Lüftungsventilatoren
Living space ventilation / Dehumidification : Drehzahlgesteuerte Ventilatoren 0…10 V DC

Operating conditions

Temperature : 0...50 °C
RelativeHumidity : 85 % nicht kondensierend
EMV/ESD : EN50082-1/2

cIO CANopen Module

Compact I/O modules for DIN rail mounting

product series of compact CANopen I/O modules with various electrical connections

Properties

Housing : Kunststoffgehäuse zum Aufrasten auf DIN-Trageschienen
Dimensions : ca. (LxBxH) 18 x 90 x 62 mm
Internal circuits : Ausgangsschutzschaltungen gegen Überspannung und elektrostasche Entladung
Fieldbus and I/O level : getrennt durch galvanische Trennung

ElectricalConnection

Operating voltage : 11...32V DC (typ. 24V DC)
Operating temperature : 0...+55 °C
Operating temperature : optional -40...+70 °C
Conductor cross-section : 0,08...1,5 mm² (AWG28...AWG14)

CAN bus properties

baud rate (max.) : 1 MBit
ciA Standards : Ds301 Version 4.2 & DS401 Version 3.0
ISO standards : ISO11898 (+ Transceiver TJA1050)
PDO : siehe Dokumente

T202

Immersible Magnetic Probe made of stainless steel (1.4571)

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil