Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		QFSK-2X
2		T203.F
3		BK-380
4		ER-104
5		XR Relais

QFSK-2X configure

1 Schwimmertyp

2 Anschlussgewinde

3 Schwimmeranzahl

4 Stablänge

5 EX

Amount

additional infomation

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

XR Relais configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Versorgungsspannung

7 Busanschluss

8 SIL

9 ATEX

Amount

additional infomation

QFSK-2X

Stainless steel float switch combination

Float switch combinations QFSK for level monitoring & level control with maximum and minimum contact sensor.

Properties

Protection class EN60529 : IP 68
Material Float : VA 1.4571
Material hose : Edelstahlwellschlauch (1.4404) mit Edelstahldrahtumflechtung (1.4301)
rod length : max. 5 m
Number of floats : bis 5
Operating temperature : max. + 150 °C
media density : ρ ≥ 0,8g/cm³
Switching system : Reed-Schalter
Contact : Wechsler, NO, NC
Switching voltage : 4...250 V AC/DC
Switching current : 1 mA ...1 A
Switching capacity : max. 1A, 60 VA/60 W
Switching hysteresis : ca. 100 mm
Switching angle : ca. + 20° / – 20°
Ex-protection : optional; IBExU10ATEX 1089
Operating pressure WFSK-25 : max. 15 bar
Operating pressure QFSK-26 : max. 6 bar

T203.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Properties

Protection class : IP 65 Dose
Sliding tube length : max. 6000 mm
Operating temperature : max. 135 °C
Operating pressure : max. 20 bar
F-Contact : 1/12 kΩ
Switching current : 1A, 2A
Switching voltage : 230 V AC

Float

quantity : max. 6
Type 05 : Oval Edelstahl 76 mm Ø | Dichte 0,81 g/cm³
Type 06 : Oval Edelstahl 90 mm Ø | Dichte 0,67 g/cm³
Minimum contact distance : Typ 05: 110 mm | Typ 06: 135 mm

Switching contacts and switching capacity

Changeover contact : max. 5x | 60 W/VA
normally open : max. 6x | 100 W/VA
Normally closed contact : max. 4x | 60 W/VA

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

ER-104

1-channel electrode relay

Electrode relays for conductive level detection for all areas in which conductive, liquid media are to be detected, controlled or monitored

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
Storage temperature : –30...+80 °C
Weight : ca. 150g
ltdata. :

Power supply

nominal voltage : siehe Typenschlüssel
AC nominal frequency : 48...62 Hz
Power consumption : max. 1 W / VA

Input

Open circuit voltage : ≤ 10 V AC
Short-circuit current : ≤ 5 mA
Switching delay : siehe Typenschlüssel
Sensitivity range : siehe Typenschlüssel

Output

Contacts : potentialfreie Wechselkontakte
Switching voltage(min) : 5 V
Switching voltage (max) : 250 V AC / 150 V DC
Overvoltage category : EN 61010-1 Kategorie III

Switching current

Switching current : min. 5 mA
Switching current : max. cos φ =1 5 A
Switching current : max. cos φ = 0,7 3 A/AC
Switching current : max. cos φ = 1

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529