Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

4 article(s) in your cart
pos.	image	product	Configure	Actions
1		QFS-55
2		ER-104
3		EFV2 24V
4		XR-4x2

QFS-55 configure

1 Ausführung

2 Kontakt

3 Schaltkontakt

4 Kabelmaterial

5 Kabellänge

6 Ex-Option

Amount

additional infomation

EFV2 24V configure

1 Sicherheitsfunktion

2 Verstellbar

3 Elektrodenanzahl

4 Verschraubungsmaterial

5 Stabmaterial

6 Anschluss

7 Anschlussgewinde

8 Kabelbruchwiderstand

9 Auswerteelektronik

10 Standaufnehmerlänge

11 SIL

Amount

additional infomation

XR-4x2 configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Empfindlichkeitsbereich

7 Versorgungsspannung

8 Busanschluss

9 SIL

10 ATEX

Amount

additional infomation

QFS-55

Teflon float switch in rod design

The float switch combination is built with float switches of the QFS-50 and QFS-60 series. This makes it possible to control a level in a simple way.

Technical Data

Material : PTFE (Teflon)
connection cable : Silikon, Teflon
Material rod : VA-Rohr, PTFE beschichtet
Operating temperature : max. +150 °C
media density : ρ ≥ 0,75 g/cm³
Switching system : Reed-Schalter
Contact : Wechsler, NO, NC
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
Ex-protection optional : Elektrische Daten siehe EG-Prüfbescheinigung IBExU10ATEX 1089

Reed contact

Switching current : 1 mA ... 1 A
Switching voltage : 24 ... 250 V AC/DC
Switching capacity : Max. 1A, 60 VA / 60 W
Switching hysteresis : ca. 100 mm
Switching angle : ca. +20°...–20°

Namur circuit (1kΩ/12kQ)

Switching current / switching voltage : nur zum Anschluss an KR-163... oder andere „Namur”-Relais
Switching hysteresis : ca. 100 mm
Switching angle : ca. +20°...–20°

ER-104

1-channel electrode relay

Electrode relays for conductive level detection for all areas in which conductive, liquid media are to be detected, controlled or monitored

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
Storage temperature : –30...+80 °C
Weight : ca. 150g
ltdata. :

Power supply

nominal voltage : siehe Typenschlüssel
AC nominal frequency : 48...62 Hz
Power consumption : max. 1 W / VA

Input

Open circuit voltage : ≤ 10 V AC
Short-circuit current : ≤ 5 mA
Switching delay : siehe Typenschlüssel
Sensitivity range : siehe Typenschlüssel

Output

Contacts : potentialfreie Wechselkontakte
Switching voltage(min) : 5 V
Switching voltage (max) : 250 V AC / 150 V DC
Overvoltage category : EN 61010-1 Kategorie III

Switching current

Switching current : min. 5 mA
Switching current : max. cos φ =1 5 A
Switching current : max. cos φ = 0,7 3 A/AC
Switching current : max. cos φ = 1

EFV2 24V

adaptive conductive electrodes with and without 24 V direct connection

The conductive electrode EFV2 is approved by the "DIBt" as an overfill prevention device for liquids hazardous to water.

Connection

Box : Polyesterdose (PO)
Cable : Kabel (TPK)
Plug : Stecker (ST)

Properties

Protection class : IP 65
connection thread : G2"
Union nut : G2¾", S 100x8
Material Screw connection : PE, PVC, PPH, PVDF
Material Sensor rods : Edelstahl (1.4571), Hastelloy C, Titan, Tantal, Kohlestifte
Operating temperature : PE, PVC: atmosphärisch PPH : 90 °C, PVDF: 100 °C
Operating pressure : atmosphärisch
Resistance value of line monitoring : 22 kΩ / 100 kΩ je nach Ausführung

Operating temperature

PE : atmosphärisch
PVC : atmosphärisch
PPH : 90 °C
PVDF : 100 °C

Technical specifications electronic part

Operating temperature : –20...+85 °C
Storage temperature : –30...+85 °C
nominal voltage : 24...30 V DC
Power consumption : max. 2 W
Switching voltage : max. 230 V AC / V DC min. 5 V DC (CMOS-Relais)
Switching current : max. 0,12 A AC / A DC min. <1 mA
Switching capacity : max. 25 VA / W
Sensitivity : 3k … 100 kΩ

XR-4x2

Electrode relay with ATEX and WHG approval

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised.

Protection class EN60529