Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

4 article(s) in your cart
pos.	image	product	Configure	Actions
1		QFS-40
2		Ex-BK
3		TK-312
4		EFV2 24V

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

Ex-BK configure

1 Ex

Amount

additional infomation

TK-312 configure

1 Housing

Amount

additional infomation

EFV2 24V configure

1 Sicherheitsfunktion

2 Verstellbar

3 Elektrodenanzahl

4 Verschraubungsmaterial

5 Stabmaterial

6 Anschluss

7 Anschlussgewinde

8 Kabelbruchwiderstand

9 Auswerteelektronik

10 Standaufnehmerlänge

11 SIL

Amount

additional infomation

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

Ex-BK

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –20...+120 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm
Dimensions : 80 mm x 75 mm x 57 mm

Material

Housing : Aluminium
Mounting clip : V2A
Rivet : V2A
Screw connection : M 20 x 1.5, V2A

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 24...250 V AC/DC
Switching current : 20 mA...6 A AC/DC
Switching capacity(min.) : max. 500 VA, 60 W
Switching capacity(max.) : min. 2 VA/W

TK-312

Evaluation unit with 0/4... 20 mA current output

The TK-312 measuring transducer converts the resistance signal supplied from a continuous level sensor into a current signal proportionate to the level.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA, 2W
Dimensions housing type B : 22,5 x 114,5 x 99
Dimensions housing type C : 22,5 x 114,5 x 114

Input

Voltage : 0...10 V
Resistance in three-wire circuit RG : 0-4...10 kW

Output

Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Current output : 0/4... 20 mA bezogen auf die Masse des Eingangs
Voltage output : 0/2... 10 V
Mounting : Tragschiene nach EN 50022
Weight : 175 g

EFV2 24V

adaptive conductive electrodes with and without 24 V direct connection

The conductive electrode EFV2 is approved by the "DIBt" as an overfill prevention device for liquids hazardous to water.

Connection

Box : Polyesterdose (PO)
Cable : Kabel (TPK)
Plug : Stecker (ST)

Properties

Protection class : IP 65
connection thread : G2"
Union nut : G2¾", S 100x8
Material Screw connection : PE, PVC, PPH, PVDF
Material Sensor rods : Edelstahl (1.4571), Hastelloy C, Titan, Tantal, Kohlestifte
Operating temperature : PE, PVC: atmosphärisch PPH : 90 °C, PVDF: 100 °C
Operating pressure : atmosphärisch
Resistance value of line monitoring : 22 kΩ / 100 kΩ je nach Ausführung