Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

8 article(s) in your cart
pos.	image	product	Configure	Actions
1		NSP-X-E
2		EFV2 24V
3		TK-313
4		XR-4x2
5		TK-315
6		T203.F
7		ZMF-202e-IR
8		T-200.L

NSP-X-E configure

1 Messbereiche

2 Gabeloberfläche

Amount

additional infomation

EFV2 24V configure

1 Sicherheitsfunktion

2 Verstellbar

3 Elektrodenanzahl

4 Verschraubungsmaterial

5 Stabmaterial

6 Anschluss

7 Anschlussgewinde

8 Kabelbruchwiderstand

9 Auswerteelektronik

10 Standaufnehmerlänge

11 SIL

Amount

additional infomation

TK-313 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

XR-4x2 configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Empfindlichkeitsbereich

7 Versorgungsspannung

8 Busanschluss

9 SIL

10 ATEX

Amount

additional infomation

TK-315 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

ZMF-202e-IR configure

1 Typ

2 Temperaturbereich

3 Messmethode

4 Signalausgang

5 Messbereich

6 Ex-Zulassung

Amount

additional infomation

NSP-X-E

Vibrating Limit Switch

The vibrating limit switch is a level limit switch for all kinds of fluids and is used in tanks, containers and pipelines.

Properties

Protection class EN60529 : IP 65/IP 67
Operating pressure : ≤ 40 bar
media density : ρ ≥ 0,7 g/cm³
Viscosity : max. 10000 mm²s
Rated current : < 15 mA
Protection class : III
Output : PNP
power : kurzschlussfest, überlastsicher
Display : LED (grün, rot)
Switching delay (cover) : ca. 0,5 s
Switching delay (release) : ca. 1 s

NSP-1-E

connection thread : G 1”
Operating temperature : –40...+150 °C
Storage temperature : –40...+85 °C
nominal voltage : 10...55 V DC (verpolsicher)
Current output : ≤ 350 mA

NSP-2-E

connection thread : G ½”
Operating temperature : –40...+100 °C
Storage temperature : –20...+70 °C
nominal voltage : 10...35 V DC (verpolsicher)
Current output : ≤ 250 mA

EFV2 24V

adaptive conductive electrodes with and without 24 V direct connection

The conductive electrode EFV2 is approved by the "DIBt" as an overfill prevention device for liquids hazardous to water.

Connection

Box : Polyesterdose (PO)
Cable : Kabel (TPK)
Plug : Stecker (ST)

Properties

Protection class : IP 65
connection thread : G2"
Union nut : G2¾", S 100x8
Material Screw connection : PE, PVC, PPH, PVDF
Material Sensor rods : Edelstahl (1.4571), Hastelloy C, Titan, Tantal, Kohlestifte
Operating temperature : PE, PVC: atmosphärisch PPH : 90 °C, PVDF: 100 °C
Operating pressure : atmosphärisch
Resistance value of line monitoring : 22 kΩ / 100 kΩ je nach Ausführung

Operating temperature

PE : atmosphärisch
PVC : atmosphärisch
PPH : 90 °C
PVDF : 100 °C

Technical specifications electronic part

Operating temperature : –20...+85 °C
Storage temperature : –30...+85 °C
nominal voltage : 24...30 V DC
Power consumption : max. 2 W
Switching voltage : max. 230 V AC / V DC min. 5 V DC (CMOS-Relais)
Switching current : max. 0,12 A AC / A DC min. <1 mA
Switching capacity : max. 25 VA / W
Sensitivity : 3k … 100 kΩ

TK-313

Evaluation unit with 2 change over limit contacts

The TK-313 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control / measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99
Dimensions housing type C : 22,5 x 114,5 x 114

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 2 Wechselkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g
ltdata. :

XR-4x2

Electrode relay with ATEX and WHG approval

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised.

Protection class EN60529

clamp : IP20
Housing : IP40

Technical Data

Operating temperature : -20...+60 °C
Storage temperature : -30...+80 °C
Output contacts : potentialfrei
Switching voltage : min. 5 V, max. 250 V AC / 150 V DC
Switching current : min. 5 mA, max. 5 A AC / 5 A DC
Switching capacity : min. 300 mW, max.100 VA / max. 50 W
CE marking : siehe Konformitätserklärung
Ex-protection/IECEx : siehe Baumusterprüfbescheinigung
Weight : ca. 170 g

TK-315

Evaluation unit with 4 limit contacts (NO-contacts)

The TK-315 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control/measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99 mm
Dimensions housing type C : 22,5 x 114,5 x 114 mm

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 4 Schließerkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g

T203.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Properties