Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		Fluidix Lub-VDT
2		BK-3X0
3		EF 3…5 24 V
4		TK-313
5		ZS-Serie

Fluidix Lub-VDT configure

1 Signalausgang

2 Messbereich

Amount

additional infomation

EF 3…5 24 V configure

1 Sicherheitsfunktion

2 Elektrodenanzahl

3 Anschlussgewinde

4 Stabmaterial

5 Stabdurchmesser

6 Beschichtung

7 Auswerteelektronik

8 Stablänge

9 SIL

Amount

additional infomation

TK-313 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

Fluidix Lub-VDT

Oil condition sensor for permanent monitoring of mechanical properties of liquids

The FluidIX Lub-VDT enables inline monitoring of mechanical fluid properties.

Properties

CE marking : EN 61000-6-1/2/3/4
Operating voltage : 9...32 V DC
Housing material : Edelstahl
Protection class : IP 67
Dimensions : 30x90 mm
Process connection : G 3/8"
Electrical connection : M12-8 A-Coding
Weight : 150g
Measurement output : 2x 4...20mA
bus protocol : ModbusRTU, CANopen

Measured variables

Resonator frequency : 20...25 kHz
Viscosity : 1-650 cSt (mm²/s)
density : 0.5-1.5 g/cm³
Temperature : -40...+125°C
sampling rate : 1/s

Operating conditions

Temperature of the fluid : -40...+125°C
Housing temperature : -40...+100°C
oil pressure : Max. 50 bar
particle size : 250 μm

BK-3X0

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

EF 3…5 24 V

Conductive electrodes with 24 V DC direct connection

The conductive electrodes EF3...5 are approved by the "DIBt" as overfill prevention devices for liquids hazardous to water.

Properties

connection : integrierter Anschlusskopf
Protection class : IP 65
connection thread : G 1¼"
Material Screw connection : PPH
Material electrode rods : Edelstahl (1.4571), Hastelloy C, Titan, Tantal
material coating : PTFE
Coating length : voll = ganzer Stab (10 mm am Stabende sind blank) teil = ca. 250 mm von oben
Rod diameter : 4 mm, 6 mm
rod length : max. 6 m
Operating temperature : 85 °C
Operating pressure : atmosphärisch
Spacer : ab Länge > 1000 mm je 1000 mm 1 Abstandshalter

Properties electronic part

Operating temperature : –20...+85 °C
Storage temperature : –30...+85 °C
nominal voltage : 24 V DC ± 15%
Power consumption : max. 2 W (Klemme A1, A2)
Switching voltage : max. 250 V AC, 150 V DC min. 5 V DC (Relais mit Kombi-Goldkontakten)
Switching current : max. 3 A AC, 3 A DC min. 1 mA
Switching capacity : max. 750 VA, 150 W
Sensitivity : 3k ... 100 kΩ in vier Stufen (3 k, 10 k, 30 k, 100 kΩ) wählbar

TK-313

Evaluation unit with 2 change over limit contacts

The TK-313 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control / measurement.

Properties