Home
Cart

Cart

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

8 article(s) in your cart
pos.	image	product	Configure	Actions
1		EFV2 20…230V
2		CS-11
3		TK-101
4		TPS-210 TPS-220
5		EF2X
6		KS-Serie
7		ZDT-Serie
8		MKL

EFV2 20…230V configure

1 Verschraubungsmaterial

2 Stabmaterial

3 Anschluss

4 Anschlussgewinde

5 Elektronikteil

6 Standaufnehmerlänge

Amount

additional infomation

TK-101 configure

1 ATEX

Amount

additional infomation

TPS-210 TPS-220 configure

1 Ausgangssignal

2 Schutzkappe

Amount

additional infomation

EF2X configure

1 Typ

2 Anschluss

3 Rohrmaterial und Anschlußkopf

4 Stabmaterial

5 Elektronikteil

Amount

additional infomation

MKL configure

1 Material

2 Anschlussflansch

3 Prozessanschluss

4 Schwimmer

5 Ablassschraube

6 Anzeige

7 Mittenentfernung

Amount

additional infomation

EFV2 20…230V

Conductive electrodes with 24...230 V direct connection

The overfill protection EFV2 (24...230 V AC/DC) is approved by the "DIBt" as overfill protection for liquids hazardous to water.

Properties

connection : Polyesterdose (PO)
Protection class : IP 65
connection thread : G2"
Union nut : G2¾" | S 100x8
Material Screw connection : PE, PVC, PPH, PVDF
Material Sensor rods : Edelstahl (1.4571), Hastelloy B, Hastelloy C, Titan, Tantal, Kohlestifte
Operating pressure : atmosphärisch
Resistance value of line monitoring : 100 kΩ
Adjustable sensitivity range : 2..100 kΩ

Operating temperature

PE : atmosphärisch
PVC : atmosphärisch
PPH : 90 °C
PVDF : 100 °C

Power supply

nominal voltage : 24...230 V AC/DC
Power consumption : ≤ 2 W

Output

potential-free changeover contacts : 2
Switching voltage : max. 250 V AC / 30 V DC
Switching current : max. 5 A AC / 5 A DC
Switching capacity : max. 750 VA / 90 W
displays : Betriebs- LED grün Funktions-LED rot
Switching delay : ca. 0,5 s

CS-11

CO2 Sensor with digital Interface

Digital CO2 sensor CS-11 for measuring carbon dioxide concentration in mobile applications.

Properties CS-11

Measured variable: : CO2
Measuring range: : 0…5.000 ppm
Measuring principle: : optisch, NDIR
Housing : Kunststoff
measuring grid : 2 sec.
Accuracy : ± 50 ppm
Protocol : I²C-Bus
Operating conditions Temperature : -0°C … 50°C
Operating conditions Humidity : 0…85 % rH
Storage conditions Temperature : -30°C … 70 °C
Storage conditions Humidity : 0…85 % rH

Properties MV-CAN

Housing : Plastik
Mounting : Hutschienenmodul für Einbau in Schaltschrank
Operating voltage : 10…48 V
measuring grid : 2 sec.
CAN protocol : CANopen 2.0 A nach CiA DS 404
Physical Layer : nach ISO 11898
Option : Bereitstellung des EDS-Files
Operating temperature : -40°C … +80°C
Storage temperature : -40°C … +120 °C

TK-101

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

TPS-210 TPS-220

Flexible, analogue dew point sensor

The dew point sensors of the enable direct measurement of the dew point and ambient temperature indoors and outdoors.

Properties TPS-210

Operating voltage : 12...30V DC
Power consumption : < 15mA

Properties TPS-220

Operating voltage : 24V DC
Loop voltage min: : Bürde(Ohm) *0,02 + 8 V
Loop voltage max: : 30V

General properties

Housing : Aluminium, eloxiert
Dimensions (in mm) : 135 x Ø 19,2

Measuring range

measuring range (Humidity) : 0…100% rH
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -50...+80°C
Measuring accuracy (temperature) : ± 0,2°C
Signal output : 0...10V | 4...20mA

EF2X

Double pipe and filling pipe monitoring

EF2L and EF2T -conductive- with general technical approval for construction Z-65.13-405

Properties

Electrical connection : Stecker GDM
Protection class EN60529 : IP 65 mit Dichtung
connection : PVC Überwurfmutter G 1 ¼“
PVC : max. +60 °C
PE : max. +80 °C
Storage temperature : -30...+85 °C
Operating pressure : max. 6 bar

Material

Pipe : PVC | PE
Sensor rods : Edelstahl 1.4571 | Hastelloy B/C | Titan | Tantal

tdata.ElektronikteilET-473L|ET-473T

nominal voltage : 20...30 V DC
Power consumption : 1 VA
Output contact : Schließer | Öffnerkontakt (NO/NC) (nicht potentialfrei)
Switching voltage : 12...30 V DC
Switching current : max. 300 mA
Switching capacity : max. 9 W
Sensitivity range : 2...30 kOhm
ltdata. :

KS-Serie

Sensors for temperature & humidity measurement

The KS series sensors are modular temperature and humidity measurement sensors in compact housings for use in almost any application.

Specifications

Housing shapes : Stabform | Alu- oder Polycarbonatgehäuse
measurands : Temperatur | relative Feuchte
Measuring range : -40...+80 °C | 0...100% rH
Signal output : 0...10 V oder 4…20 mA
Power supply : 12...30 V DC | 24 V DC

ZDT-Serie

Differential pressure transmitter for high or low pressure applications

Versatile and reliable differential pressure transmitter for measuring air, non-aggressive media as well as liquids and oils.

Properties

Pressure type : Differenzdruck
Housing : Kunststoff
LCD display : optional
Signal output : 0…10 V | 4…20 mA

Measurement parameters

Total error : ± 2,5 % FS (typ. ± 0,5 %)
Linearity error : ± 1 % FS

Operating conditions

Operating temperature : 0...+50 °C
Storage temperature : -20°C...+120°C

MKL

Magnetic Flap Indicator

The MKL level indicator is connected by its two connections to the container to be monitored (see connection example). According to the law of interconnected containers the level in the float chamber corresponds exactly to the level in the container

Properties