Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

6 article(s) in your cart
pos.	image	product	Configure	Actions
1		Ex-BK
2		ZMF-100-IR
3		Fluidix Lub-VDT
4		TK-313
5		ÜTA-32
6		ZDT-H

Ex-BK configure

1 Ex

Amount

additional infomation

ZMF-100-IR configure

1 Output signal

2 Measuring range

Amount

additional infomation

Fluidix Lub-VDT configure

1 Signalausgang

2 Messbereich

Amount

additional infomation

TK-313 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

Ex-BK

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –20...+120 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm
Dimensions : 80 mm x 75 mm x 57 mm

Material

Housing : Aluminium
Mounting clip : V2A
Rivet : V2A
Screw connection : M 20 x 1.5, V2A

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 24...250 V AC/DC
Switching current : 20 mA...6 A AC/DC
Switching capacity(min.) : max. 500 VA, 60 W
Switching capacity(max.) : min. 2 VA/W

ZMF-100-IR

gas detector with 4...20mA signal output

industrial CO2 sensor ZMF-100-IR with a measuring range of up to 50,000ppm

Product features

Measuring principle : optisch, NDIR (nicht-dispersive Infrarot-Absorptionsmessung)
Operating voltage : 24 V DC / 100 mA
Heating time : ca. 5 min
Response time : ca. 30 s
Repeatability : +/- 1%
Housing : Aluminium (rot) IP54
Weight : ca. 500g
Shaft range : 4,27 - 4,35 µm (4270-4350 nm)
Gas ingress : per Diffusion

ambient conditions

Operating temperature range : -10...+50 °C
Storage temperature range : -40...+100 °C
RelativeHumidity : 15..95 %
Air pressure : 900...1100 hPa

Fluidix Lub-VDT

Oil condition sensor for permanent monitoring of mechanical properties of liquids

The FluidIX Lub-VDT enables inline monitoring of mechanical fluid properties.

Properties

CE marking : EN 61000-6-1/2/3/4
Operating voltage : 9...32 V DC
Housing material : Edelstahl
Protection class : IP 67
Dimensions : 30x90 mm
Process connection : G 3/8"
Electrical connection : M12-8 A-Coding
Weight : 150g
Measurement output : 2x 4...20mA
bus protocol : ModbusRTU, CANopen

Measured variables

Resonator frequency : 20...25 kHz
Viscosity : 1-650 cSt (mm²/s)
density : 0.5-1.5 g/cm³
Temperature : -40...+125°C
sampling rate : 1/s

Operating conditions

Temperature of the fluid : -40...+125°C
Housing temperature : -40...+100°C
oil pressure : Max. 50 bar
particle size : 250 μm

TK-313

Evaluation unit with 2 change over limit contacts

The TK-313 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control / measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99
Dimensions housing type C : 22,5 x 114,5 x 114

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 2 Wechselkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g
ltdata. :

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties