Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

9 article(s) in your cart
pos.	image	product	Configure	Actions
1		TK-313
2		ESE
3		EE-2X
4		Fluidix Lub-VDT
5		XR Relais
6		TK-101
7		LGW-13
8		KS-17
9		KS-410 KS-420

TK-313 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

ESE configure

1 Measurend

2 Safetyfunction

3 Direction

4 measuring-range

Amount

additional infomation

EE-2X configure

1 Typ

2 Elektrodenanzahl

3 Anschlussgewinde

4 Stabmaterial

5 Stabdurchmesser

6 Beschichtung

7 Stablänge

8 SIL2

Amount

additional infomation

Fluidix Lub-VDT configure

1 Signalausgang

2 Messbereich

Amount

additional infomation

TK-101 configure

1 ATEX

Amount

additional infomation

TK-313

Evaluation unit with 2 change over limit contacts

The TK-313 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control / measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99
Dimensions housing type C : 22,5 x 114,5 x 114

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 2 Wechselkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g
ltdata. :

ESE

Switching channel extension for ES series

TÜV-certified, type-tested electronic safety switching device (SIL2)

Properties

Operating voltage : 16...32 V DC (max. 5,9 W)
Dimensions : 150 x 60 x 42 mm (L x B x H)
Housing : Aluminium (eloxiert)
Protection class : IP65

Approvals

DGRL 2014/68/EU Kat:IV : Baumustergeprüft gemäß Druckgeräterichtlinie
DIN EN12263:1998 : Kälteanlagen und Wärmepumpen Sicherheitsschalteinrichtungen zur Druckbegrenzung -Anforderungen und Prüfungen; Kategorie IV
DIN EN378:2020 : Kälteanlagen und Wärmepumpen - Sicherheitstechnische und umweltrelevante Anforderungen
DIN EN61508:2011 : SIL2

Measuring ranges

Measuring range relative pressure (nominal pressure) : -1…500 bar
Measuring range differential pressure (nominal pressure) : 0…1 mbar - 0…1.000 mbar
Setting accuracy (from nominal pressure) : 0,1 %

Operating conditions

Pressure type : Relativdruck, Differenzdruck
Temperature of the fluid : -40…+125 °C
Ambient temperature : -20…+65 °C
Parts in contact with media : Edelstahl

process connection

Version relative pressure : G ¼“ Innengewinde
Version differential pressure : G ⅛“ Innengewinde
Adapter for process connection : 6mm; 8mm oder 10mm

electrical connection

Analogue current output : 1x 4…20 mA
Digital inputs/outputs : 2x Alarm oder 1x Alarm & 1x Fernentriegelung

Load capacity of the switching contacts DC (24V)

DC1 : 16 A
DC13 : 1,5A

Load capacity of the switching contacts AC (230V)

AC1 : 16 A
AC3 : 10 A
AC15 : 7 A

EE-2X

electrode, multiple for Ex-Zone 0 (Cat. 1)

The conductive electrodes of the EE-21/EE-22 series enable the monitoring of conductive liquids within the Ex area Zone 0 (Cat. 1).

Variants

cable connection on side : EE-21
cable connection on top : EE-22

Properties

connection : Edelstahl (1.4571)
Protection class EN60529 : IP65
Ex-protection : TÜV 02 ATEX 1796 X
Ex protection type : II 1 G Ex ia IIC T6 bzw. Ex ia IIB T6 / II ½ G Ex ia IIC T6 bzw. Ex ia IIB T6
connection thread : G1" | G1¼"
Cable entry EE-21 : Edelstahl (1.4571)
Cable entry EE-22 : Kunststoff
Rod diameter : 4 mm | 6 mm
rod length : max. 6.000 mm
Operating pressure media side : max. 40 bar
Spacer : ab Länge > 1000 mm je 1 pro 1000 mm

Material

electrode body : Edelstahl (1.4571)
Seal (head) : Viton
Seal (media side) : Viton | PTFE
Potential equalisation conductor connection : Edelstahl (1.4571)
electrode rods : Edelstahl (1.4571) | Hastelloy C | Tantal
Coating : PTFE

Operating temperature

Category 1 Class T6...T1 : 60 °C
Category 2 Class T6 : 80 °C
Category 2 Class T5 : 95 °C
Category 2 Class T4 : 130 °C (100°C)
Category 2 Class T3...T1 : 150 °C (100°C)

Fluidix Lub-VDT

Oil condition sensor for permanent monitoring of mechanical properties of liquids

The FluidIX Lub-VDT enables inline monitoring of mechanical fluid properties.

Properties

CE marking : EN 61000-6-1/2/3/4
Operating voltage : 9...32 V DC
Housing material : Edelstahl
Protection class : IP 67
Dimensions : 30x90 mm
Process connection : G 3/8"
Electrical connection : M12-8 A-Coding
Weight : 150g
Measurement output : 2x 4...20mA
bus protocol : ModbusRTU, CANopen

Measured variables

Resonator frequency : 20...25 kHz
Viscosity : 1-650 cSt (mm²/s)
density : 0.5-1.5 g/cm³
Temperature : -40...+125°C
sampling rate : 1/s

Operating conditions

Temperature of the fluid : -40...+125°C
Housing temperature : -40...+100°C
oil pressure : Max. 50 bar
particle size : 250 μm

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529

clamp : IP20
Housing : IP40

Technical Data

Operating temperature : -20...+60 °C
Storage temperature : -30...+80 °C
Output contacts : potentialfrei
Switching voltage : min. 5 V | max. 250 V AC / 150 V DC
Switching current : min. 5 mA | max. 5 A AC / 5 A DC
Switching capacity : min. 300 mW | max. 100 VA / 50 W
Quiescent current : umschaltbar
Weight : ca. 250 g
CE marking : siehe Konformitätserklärung
Ex-protection/IECEx : siehe Prüfbescheinigung

TK-101

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

LGW-13

CO2 sensor for measuring room air quality with visual and acoustic warning signal output

Multifunctional CO2 sensor with LED display and acoustic alarm, equipped with switching functions for both industrial and private applications (0...3.000ppm)

Product features

Product type : CO2-Sensor zur Bewertung und Überwachung der Luftgüte
Measuring principle : Basierend auf optischem Messprinzip (NDIR)
Measuring range : Lieferbar in unterschiedlichen Messbereichen (Standard 0…3.000ppm)
Display : Darstellung der CO2-Konzentration mittels Bargraphanzeige (Luftgüteampel)
Switching output : Einstellbarer potentialfreier Schaltausgang
Signal output : 4...20 mA und 0...10 V Signalausgang (nur bei der Variante L)
Alarm : Akustischer Alarmmelder (je nach eingestellten CO2-Grenzwerten)
further function : Integrierte Funktionsüberwachung
Housing : Kompaktes IP 20 Wandgehäuse (Polycarbonat, weiß)
Extension : Mögliche Erweiterung um Temperaturmessung
Assembly : Erhältlich als Tischgerät mit Netzteil oder zur Wand- & Aufputzmontage ohne Netzteil