Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		QFS-40
2		XR Relais
3		T-200.L
4		TK-313
5		T200.F

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

XR Relais configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Versorgungsspannung

7 Busanschluss

8 SIL

9 ATEX

Amount

additional infomation

T-200.L configure

1 Länge

2 Anschluss

3 Anschlussgewinde

4 Befestigungswinkel

5 Schwimmertyp

Amount

additional infomation

TK-313 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529

clamp : IP20
Housing : IP40

Technical Data

Operating temperature : -20...+60 °C
Storage temperature : -30...+80 °C
Output contacts : potentialfrei
Switching voltage : min. 5 V | max. 250 V AC / 150 V DC
Switching current : min. 5 mA | max. 5 A AC / 5 A DC
Switching capacity : min. 300 mW | max. 100 VA / 50 W
Weight : ca. 170g
CE marking : siehe Konformitätserklärung
Ex-protection/IECEx : siehe Prüfbescheinigung

T-200.L

Leakage probes with general building authority approval

The leakage probes T-200.L are approved by the "DIBt" on the basis of the "WasBauPVO" for the detection of leaked liquids hazardous to water.

Connection

Box : Polyesterdose (PO)
Box : Polyethylen-Anschlusskopf (PE)
Cable : Kabel (TPK)
Plug : Stecker (ST)

Properties

Protection class : IP 65
Cable entry : PVDF-Verschraubung , PVC-Dichtung
Material Float : PE
Material leakage probe base : PE
Cable : TPK (PVC Basis)
Operating temperature : atmosphärisch
Operating pressure : atmosphärisch
media density : mit Schwimmer PE 52 ρ ≥ 1,05 g/cm³
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Resistance value

Operational readiness : ca. 1 kΩ
Leakage detection : ca. 12 kΩ

TK-313

Evaluation unit with 2 change over limit contacts

The TK-313 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control / measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99
Dimensions housing type C : 22,5 x 114,5 x 114

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 2 Wechselkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g
ltdata. :

T200.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection