Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

10 article(s) in your cart
pos.	image	product	Configure	Actions
1		TK-309-0
2		ZMF-100-IR
3		XR Relais
4		ESE
5		TPS-410 TPS-420
6		CS-11
7		T203.F
8		CSC-20 YUGO
9		T204
10		T204-0.F

TK-309-0 configure

1 Gewinde

2 Schwimmerausführung

3 Anschluss

4 Rohrlänge

5 Auflösung

6 Explosionsschutz

7 Zubehör

Amount

additional infomation

ZMF-100-IR configure

1 Output signal

2 Measuring range

Amount

additional infomation

XR Relais configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Versorgungsspannung

7 Busanschluss

8 SIL

9 ATEX

Amount

additional infomation

ESE configure

1 Measurend

2 Safetyfunction

3 Direction

4 measuring-range

Amount

additional infomation

TK-309-0

Stainless steel level sensor for Ex-Zone 0 (Cat.1)

T30... continuous magnetic immersible probes are used for quasi-acquisition of the filling level in containers with liquid media.

Technical Data

Protection class Socket : IP65
Float type : Typ 07
Sliding tube length : max. 6000 mm
Operating temperature : max. 135 °C
Operating pressure : max. 20 bar
media density : Typ 07: 0,54 g/cm³
Resolution : 7,5 mm | 10mm |15 mm | 20 mm
Accessories : R/I-Wandler TK-101

ZMF-100-IR

gas detector with 4...20mA signal output

industrial CO2 sensor ZMF-100-IR with a measuring range of up to 50,000ppm

Product features

Measuring principle : optisch, NDIR (nicht-dispersive Infrarot-Absorptionsmessung)
Operating voltage : 24 V DC / 100 mA
Heating time : ca. 5 min
Response time : ca. 30 s
Repeatability : +/- 1%
Housing : Aluminium (rot) IP54
Weight : ca. 500g
Shaft range : 4,27 - 4,35 µm (4270-4350 nm)
Gas ingress : per Diffusion

ambient conditions

Operating temperature range : -10...+50 °C
Storage temperature range : -40...+100 °C
RelativeHumidity : 15..95 %
Air pressure : 900...1100 hPa

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529

clamp : IP20
Housing : IP40

Technical Data

Operating temperature : -20...+60 °C
Storage temperature : -30...+80 °C
Output contacts : potentialfrei
Switching voltage : min. 5 V | max. 250 V AC / 150 V DC
Switching current : min. 5 mA | max. 5 A AC / 5 A DC
Switching capacity : min. 300 mW | max. 100 VA / 50 W
Weight : ca. 170g
CE marking : siehe Konformitätserklärung
Ex-protection/IECEx : siehe Prüfbescheinigung

ESE

Switching channel extension for ES series

TÜV-certified, type-tested electronic safety switching device (SIL2)

Properties

Operating voltage : 16...32 V DC (max. 5,9 W)
Dimensions : 150 x 60 x 42 mm (L x B x H)
Housing : Aluminium (eloxiert)
Protection class : IP65

Approvals

DGRL 2014/68/EU Kat:IV : Baumustergeprüft gemäß Druckgeräterichtlinie
DIN EN12263:1998 : Kälteanlagen und Wärmepumpen Sicherheitsschalteinrichtungen zur Druckbegrenzung -Anforderungen und Prüfungen; Kategorie IV
DIN EN378:2020 : Kälteanlagen und Wärmepumpen - Sicherheitstechnische und umweltrelevante Anforderungen
DIN EN61508:2011 : SIL2

Measuring ranges

Measuring range relative pressure (nominal pressure) : -1…500 bar
Measuring range differential pressure (nominal pressure) : 0…1 mbar - 0…1.000 mbar
Setting accuracy (from nominal pressure) : 0,1 %

Operating conditions

Pressure type : Relativdruck, Differenzdruck
Temperature of the fluid : -40…+125 °C
Ambient temperature : -20…+65 °C
Parts in contact with media : Edelstahl

process connection

Version relative pressure : G ¼“ Innengewinde
Version differential pressure : G ⅛“ Innengewinde
Adapter for process connection : 6mm; 8mm oder 10mm

electrical connection

Analogue current output : 1x 4…20 mA
Digital inputs/outputs : 2x Alarm oder 1x Alarm & 1x Fernentriegelung

Load capacity of the switching contacts DC (24V)

DC1 : 16 A
DC13 : 1,5A

Load capacity of the switching contacts AC (230V)

AC1 : 16 A
AC3 : 10 A
AC15 : 7 A

TPS-410 TPS-420

Compact, analogue dew point sensor

The dew point sensors of the enable direct measurement of the dew point and ambient temperature indoors and outdoors.

Properties TPS-410

Operating voltage : 12...30V DC
Power consumption : < 15mA
Protection class : Gehäuse IP66, Stecker IP 67
Weight : 96g

Properties TPS-420

Operating voltage : 24V DC
Loop voltage min: : Bürde(Ohm) *0,02 + 8 V
Loop voltage max: : 30V

General properties

Housing : Aluminium, eloxiert
Dimensions (in mm) : 135 x Ø 19,2

Measuring range

measuring range (dew point) : -50…+80 °C
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -40...+80°C
Measuring accuracy (temperature) : ± 0,2°C
Signal output : 0...10V | 4...20mA

CS-11

CO2 Sensor with digital Interface

Digital CO2 sensor CS-11 for measuring carbon dioxide concentration in mobile applications.

Properties CS-11

Measured variable: : CO2
Measuring range: : 0…5.000 ppm
Measuring principle: : optisch, NDIR
Housing : Kunststoff
measuring grid : 2 sec.
Accuracy : ± 50 ppm
Protocol : I²C-Bus
Operating conditions Temperature : -0°C … 50°C
Operating conditions Humidity : 0…85 % rH
Storage conditions Temperature : -30°C … 70 °C
Storage conditions Humidity : 0…85 % rH

Properties MV-CAN

Housing : Plastik
Mounting : Hutschienenmodul für Einbau in Schaltschrank
Operating voltage : 10…48 V
measuring grid : 2 sec.
CAN protocol : CANopen 2.0 A nach CiA DS 404
Physical Layer : nach ISO 11898
Option : Bereitstellung des EDS-Files
Operating temperature : -40°C … +80°C
Storage temperature : -40°C … +120 °C

T203.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Properties

Protection class : IP 65 Dose
Sliding tube length : max. 6000 mm
Operating temperature : max. 135 °C
Operating pressure : max. 20 bar
F-Contact : 1/12 kΩ
Switching current : 1A, 2A
Switching voltage : 230 V AC

Float

quantity : max. 6
Type 05 : Oval Edelstahl 76 mm Ø | Dichte 0,81 g/cm³
Type 06 : Oval Edelstahl 90 mm Ø | Dichte 0,67 g/cm³
Minimum contact distance : Typ 05: 110 mm | Typ 06: 135 mm

Switching contacts and switching capacity

Changeover contact : max. 5x | 60 W/VA
normally open : max. 6x | 100 W/VA
Normally closed contact : max. 4x | 60 W/VA

CSC-20 YUGO

Decentralised control unit, equipped with a CO2 sensor for needs-based ventilation

Decentralised CO2 monitoring with direct control of various supply and exhaust air elements such as fans and dampers (0..10.000 ppm)

Properties

Power supply : 230 V AC
measuring range (CO2) : 0..10.000 ppm
Measuring accuracy CO2 : ± 50ppm +3 % vom Messwert
Operating conditions : 0…50°C / 0…85 %rH
Storage conditions : -30…70°C / 0…85 %rH
Protection class : IP 31
EMV/ESD : EN 50082-1, EN 50082-2
Signal output : I²C

T204

Magnetic immersion probe made of stainless steel (1.4571)

For use with highly aggressive liquid media to detect level limit values in containers. Suitable for use in hazardous areas, zone 0 (category 1).

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
connection thread : G1 1/2" | G2"
Sliding tube length : max. 6000 mm (Rohr Ø 12 mm)
Operating pressure : max. 20 bar (Kugel) | max. 15 bar (Zylinder)
Operating temperature : max. 135 °C
Number of floats : max. 4

Float type

Stainless steel ball 52mm ⌀ : Dichte: 0,75 g/cm³ | mind. Kontaktabstand: 75 mm
Stainless steel ball 62mm ⌀ : Dichte: 0,65 g/cm³ | mind. Kontaktabstand: 85 mm
Stainless steel cylinder 44 mm Ø : Dichte: 0,76 g/cm³ | mind. Kontaktabstand: 75 mm

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 4
normally open : 6
Normally closed contact : 4

T204-0.F

für Ex-Zone 0 (Kat. 1)

Die Magnettauchsonden T20... dienen zur Erfassung von Füllstandsgrenzwerten in Behältern für flüssige Medien, wobei im Gasraum über der Flüssigkeit eine explosionsfähige Atmosphäre der Zone 0 (Kat. 1) und außerhalb des Behälters, im Bereich der Anschlussdose, Ex-Zone 1 (Kat. 2), gegeben ist.

Properties