Home
Cart

Cart

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		QFS-3X
2		BK-380
3		T209-0
4		TK-101
5		T205-0.F

QFS-3X configure

1 Schwimmertyp

2 Kontakt

3 Schaltkontakt

4 Hysterese

5 Kabelmaterial

6 Kabellänge

7 EX

Amount

additional infomation

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

TK-101 configure

1 ATEX

Amount

additional infomation

QFS-3X

Mercury-free float switch with µ-switch

Properties

Protection class EN60529 : IP 68
Cable entry : PVC , PTFE bzw. PVDF
Conductor cross-section : 3 x 0,75 mm², PUR 3x 0,5mm²
Operating pressure cylinder : max. 1 bar
Operating pressure sphere : max. 2 bar
Switching system : µ-Schalter
Contact : Wechsler, NO, NC

Material Float

QFS-30 : PPH (Polypropylen)
QFS-31 : PPH (Polypropylen)
QFS-34 : PE (Polyethylen)

Cable

TPK : PVC Basis Ø 5,9 mm
TPKV : PVC verstärkt Ø 7,3 mm
PUR : Polyurethan Ø 5,4 mm
SIL : Silikon Ø 6,4 mm
FEP : Teflon Ø 4,0 mm
AEM : Ethylen-Acrylat-Kautschuk

Cable length between float & attachment

TPK : 70 mm
TPKV : 90mm
PUR : 100mm
SIL : 80 mm
FEP : 110 mm
AEM : abhängig vom Innenkabel

Operating temperature

TPK(V), AEM : max. + 60 °C
PUR : max. + 70 °C
Silicone,Tefloncable with PE float : max. + 80 °C
Silicone, Teflon cable with PP float : max. + 85 °C

MaterialDensity

QFS-31 : ≥≥ 0,6 g/cm³
QFS-34 : ≥≥ 0,75 g/cm³
QFS-30 TPK(V) cable : ≥≥ 0,85 g/vcm³
QFS-30 PUR cable : ≥≥ 0,95 g/cm³
QFS-30 SIL cable : ≥≥ 0,90 g/cm³
QFS-30 FEP cable : ≥≥ 0,95 g/cm³
QFS-30AEM cable : ≥≥ 0,90 g/cm³

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

T209-0

Immersible Magnetic Probe made of PVC, PE, PPH, PTFE or stainless steel (1.4571)

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

connection : PO-Dose oder AA-Dose
Protection class : IP 65 Dose
Float type : max. 6x Kugel Edelstahl 105 mm Ø
Sliding tube length : max. 6000 mm
Operating temperature : max. 135 °C
Operating pressure : max. 20 bar
media density : 0,54 g/cm³
Number of contacts : max. 7x Wechsler / max. 10x Schließer / 7x Öffner
Switching current : 1A, 2A
Switching capacity : Wechsler 60W/VA | Schließer 100 W/VA | Öffner 60 W/VA
min. contact distance with several floats : 125 mm

TK-101

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

T205-0.F

Ex area zone 0 (category 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties