Home
Cart

Cart

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		ZS-1
2		QFS-40
3		ER-104
4		XR-4x2
5		TK-101

ZS-1 configure

1 Signalausgang

2 Druckmessbereich

3 Prozessanschluss

Amount

additional infomation

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

XR-4x2 configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Empfindlichkeitsbereich

7 Versorgungsspannung

8 Busanschluss

9 SIL

10 ATEX

Amount

additional infomation

TK-101 configure

1 ATEX

Amount

additional infomation

ZS-1

Differential pressure sensor for low pressure

Compact and robust differential pressure transmitter for measurement on air and other non-aggressive media

Properties

Pressure type : Differenzdruck
Housing : Aluminium
medium : Luft und nicht aggressive Gase

Measurement parameters

response time : < 2,5 s
Hysteresis : 0,1 %
Overload capacity : 4* fach bis 500 mbar, darüber 2* fach
Signal output selection : 0...10 V | 4...20 mA, 2-Leiter

Operating conditions

Operating voltage : 24 VDC/AC ±10 % (0...10 V) | 15...30 VDC (4...20 mA)
Operating temperature : -20...+50 °C

Connections

Electrical connection : Schraubklemme im Gehäuse
Process connection : Schlauchanschluss 4 mm oder 6 mm
Cable gland : PG 7

Pressure measuring range

0...0,25mbar :
0...0,5mbar :
0...1mbar :
0...2,5mbar :

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

ER-104

1-channel electrode relay

Electrode relays for conductive level detection for all areas in which conductive, liquid media are to be detected, controlled or monitored

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
Storage temperature : –30...+80 °C
Weight : ca. 150g
ltdata. :

Power supply

nominal voltage : siehe Typenschlüssel
AC nominal frequency : 48...62 Hz
Power consumption : max. 1 W / VA

Input

Open circuit voltage : ≤ 10 V AC
Short-circuit current : ≤ 5 mA
Switching delay : siehe Typenschlüssel
Sensitivity range : siehe Typenschlüssel

Output

Contacts : potentialfreie Wechselkontakte
Switching voltage(min) : 5 V
Switching voltage (max) : 250 V AC / 150 V DC
Overvoltage category : EN 61010-1 Kategorie III

Switching current

Switching current : min. 5 mA
Switching current : max. cos φ =1 5 A
Switching current : max. cos φ = 0,7 3 A/AC
Switching current : max. cos φ = 1

XR-4x2

Electrode relay with ATEX and WHG approval

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised.

Protection class EN60529