Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

5 article(s) in your cart
pos.	image	product	Configure	Actions
1		TPS-410 TPS-420
2		ZDS-N
3		T204
4		CS-11
5		XR Relais

TPS-410 TPS-420

Compact, analogue dew point sensor

The dew point sensors of the enable direct measurement of the dew point and ambient temperature indoors and outdoors.

Properties TPS-410

Operating voltage : 12...30V DC
Power consumption : < 15mA
Protection class : Gehäuse IP66, Stecker IP 67
Weight : 96g

Properties TPS-420

Operating voltage : 24V DC
Loop voltage min: : Bürde(Ohm) *0,02 + 8 V
Loop voltage max: : 30V

General properties

Housing : Aluminium, eloxiert
Dimensions (in mm) : 135 x Ø 19,2

Measuring range

measuring range (dew point) : -50…+80 °C
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -40...+80°C
Measuring accuracy (temperature) : ± 0,2°C
Signal output : 0...10V | 4...20mA

ZDS-N

Precision pressure switch for low pressure applications

Can be used in oil, brake fluid, diesel, air and other gases. With very good stability and overpressure resistance.

technical properties

Pressure range : 0...500mbar gestuft
supply : 12 - 24 V DC
Output : Relais 230 V/1A
overload : 2 x Messbereich
Med. connection : Schlauch
electrical connection : Schraubklemme
feature : Tasten, LCD-Anz.

T204

Magnetic immersion probe made of stainless steel (1.4571)

For use with highly aggressive liquid media to detect level limit values in containers. Suitable for use in hazardous areas, zone 0 (category 1).

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
connection thread : G1 1/2" | G2"
Sliding tube length : max. 6000 mm (Rohr Ø 12 mm)
Operating pressure : max. 20 bar (Kugel) | max. 15 bar (Zylinder)
Operating temperature : max. 135 °C
Number of floats : max. 4

Float type

Stainless steel ball 52mm ⌀ : Dichte: 0,75 g/cm³ | mind. Kontaktabstand: 75 mm
Stainless steel ball 62mm ⌀ : Dichte: 0,65 g/cm³ | mind. Kontaktabstand: 85 mm
Stainless steel cylinder 44 mm Ø : Dichte: 0,76 g/cm³ | mind. Kontaktabstand: 75 mm

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 4
normally open : 6
Normally closed contact : 4

CS-11

CO2 Sensor with digital Interface

Digital CO2 sensor CS-11 for measuring carbon dioxide concentration in mobile applications.

Properties CS-11

Measured variable: : CO2
Measuring range: : 0…5.000 ppm
Measuring principle: : optisch, NDIR
Housing : Kunststoff
measuring grid : 2 sec.
Accuracy : ± 50 ppm
Protocol : I²C-Bus
Operating conditions Temperature : -0°C … 50°C
Operating conditions Humidity : 0…85 % rH
Storage conditions Temperature : -30°C … 70 °C
Storage conditions Humidity : 0…85 % rH

Properties MV-CAN

Housing : Plastik
Mounting : Hutschienenmodul für Einbau in Schaltschrank
Operating voltage : 10…48 V
measuring grid : 2 sec.
CAN protocol : CANopen 2.0 A nach CiA DS 404
Physical Layer : nach ISO 11898
Option : Bereitstellung des EDS-Files
Operating temperature : -40°C … +80°C
Storage temperature : -40°C … +120 °C

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529