Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

6 article(s) in your cart
pos.	image	product	Configure	Actions
1		TK-315
2		T204
3		BI
4		ER-104
5		BK-380
6		T200

TK-315 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

BI configure

1 Kontaktart

2 Kabelart

3 Kabellänge

4 Befestigung

Amount

additional infomation

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

TK-315

Evaluation unit with 4 limit contacts (NO-contacts)

The TK-315 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control/measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99 mm
Dimensions housing type C : 22,5 x 114,5 x 114 mm

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 4 Schließerkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g

T204

Magnetic immersion probe made of stainless steel (1.4571)

For use with highly aggressive liquid media to detect level limit values in containers. Suitable for use in hazardous areas, zone 0 (category 1).

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
connection thread : G1 1/2" | G2"
Sliding tube length : max. 6000 mm (Rohr Ø 12 mm)
Operating pressure : max. 20 bar (Kugel) | max. 15 bar (Zylinder)
Operating temperature : max. 135 °C
Number of floats : max. 4

Float type

Stainless steel ball 52mm ⌀ : Dichte: 0,75 g/cm³ | mind. Kontaktabstand: 75 mm
Stainless steel ball 62mm ⌀ : Dichte: 0,65 g/cm³ | mind. Kontaktabstand: 85 mm
Stainless steel cylinder 44 mm Ø : Dichte: 0,76 g/cm³ | mind. Kontaktabstand: 75 mm

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 4
normally open : 6
Normally closed contact : 4

BI

Bistable Switch

Properties

Protection class : IP 65
Switching current : max. 1 A
Switching voltage : max. 24 V
Switching capacity : max. 20 W/VA

Material

Housing : Messingrohr Ø 10 x 1
Cable : TPK (PVC basis) | SIL (Silikon)

Operating temperature

TPK : –15 ° ... + 60 °C
SIL : –15 ° ... +130 °C

ER-104

1-channel electrode relay

Electrode relays for conductive level detection for all areas in which conductive, liquid media are to be detected, controlled or monitored

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
Storage temperature : –30...+80 °C
Weight : ca. 150g
ltdata. :

Power supply

nominal voltage : siehe Typenschlüssel
AC nominal frequency : 48...62 Hz
Power consumption : max. 1 W / VA

Input

Open circuit voltage : ≤ 10 V AC
Short-circuit current : ≤ 5 mA
Switching delay : siehe Typenschlüssel
Sensitivity range : siehe Typenschlüssel

Output

Contacts : potentialfreie Wechselkontakte
Switching voltage(min) : 5 V
Switching voltage (max) : 250 V AC / 150 V DC
Overvoltage category : EN 61010-1 Kategorie III

Switching current

Switching current : min. 5 mA
Switching current : max. cos φ =1 5 A
Switching current : max. cos φ = 0,7 3 A/AC
Switching current : max. cos φ = 1

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

T200

Immersible Magnetic Probe made of PVC, PE, PPH, PTFE or stainless steel (1.4571)

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil