Home
Cart

Cart

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

8 article(s) in your cart
pos.	image	product	Configure	Actions
1		BK-3X0
2		T-200.F Ex
3		TRM-100
4		TK-315
5		TSL-CAN-03
6		ÜTA-32
7		EK-CAN
8		ELH

T-200.F Ex configure

1 Führungsrohr

2 Sicherheitsfunktion

3 Rohrmaterial

4 Anschlussgewinde

5 Ausführung

6 Schaltkontakte

7 Schwimmermaterial

8 Anschlussdose

9 Länge

10 EX

Amount

additional infomation

TRM-100 configure

1 Material

2 Measuringrange

3 Connection

4 Flange

5 Sealing

Amount

additional infomation

TK-315 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

BK-3X0

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

T-200.F Ex

Overfill protection for containers with Ex approval

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

Box : Ex-Polyester
Box : Ex-Aluminium

Properties

Protection class EN60529 : IP 65
connection thread : G2"
Union nut : G 2¾"
Guide tube length : max. 6 m
Operating temperature : -20…+60 °C
Operating pressure : max. 6 bar je nach Ausführung
media density : ρ ≥ 0,72 g/cm³ (je nach Schwimmertyp)
Switching hysteresis : 2 mm
Switching point tolerance : max. 2 mm

Resistance value

Operational readiness : ca. 1 kΩ
overfill alarm : ca. 12 kΩ
Switching time : ca. 20 ms
Ex-protection : siehe Baumusterprüfbescheinigung
CE marking : siehe Konformitätserklärung

TRM-100

Turbidimeter (0...1.000 FNU or 500...4.000 FAU)

The turbidimeter TRM-100 is a compact device for measuring turbidity in liquids. The "turbidity" is measured using the scattered light method (angle 90 degrees) for the turbidity range of < 1,000 FNU (Formazine Nephelometric Units) and the transmitted light method (angle 0 degrees) for the turbidity ranges > 1,000 FAU (Formazine Attenuation Units).

Properties

Operating pressure : max. 10 bar @ 20 °C | max. 2,5 bar @ 60 °C
Measuring range : 500...4.000 FNU / FAU
Measuring accuracy : +/-5 %
Mounting position : horizontal
Process connection : DN 20 | DN 40
Flange connection : >= DN 20
number of senders : 2
number of receivers : 1

Material

Seal : EPDM | optional FPM (Viton)
Process connection : PVC | PPH
Measuring tube : Borsilikatglas mit Nano Beschichtung

Input

Power supply : 18...30 V DC
Power consumption : < 2 W

Output

Output contact : 4...20 mA
Switching delay (adjustable) : 1...10 s
Protection class : IP 65
Switching voltage : max. 250 V AC | max. 115 V DC
Switching current : max. 3 A
Switching capacity : max. 500 VA, 60 Watt
Potential-free changeover contact : 1 @ 1...10 s

TK-315

Evaluation unit with 4 limit contacts (NO-contacts)

The TK-315 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control/measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99 mm
Dimensions housing type C : 22,5 x 114,5 x 114 mm

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 4 Schließerkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g

TSL-CAN-03

Temperature sensor with CAN bus interface for air temperature measurement

CANopen transmitter for temperature measurement in media, semiconductor sensor

Properties

Measuring range : -40…+80 °C
deviation : ± 0,3 K (10...80 °C)
Measuring element : Halbleiter-Diodenfühler
measuring resolution : 0,1 K
measuring grid : ab 5 ms

ElectricalConnection

CAN protocol : CANopen 2.0 A, nach ciA DS 404
Physical Layer : nach DIN 11898
Operating voltage : 10...48 V

Operating conditions

Operating temperature : -40...+80 °C
Storage temperature : -40°C...+120°C
Shock resistance : 30g, Dauer: 14 ms bei Raumtemperatur
Vibration resistance : 10g bei 20 bis 1000 Hz
Minimumairspeedrequiredformeasurementacrossthesensor : 1,5 m/s

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties

connection : G 1” (andere Gewinde auf Anfrage)
max.length guide tube : siehe Diagramm
Operating temperature : atmosphär. Bedingungen
Operating pressure : atmosphär. Bedingungen
media density : siehe Eintauchtiefe
Number of contacts : beliebig
Contact load : max. 10 VA, max. 230 V AC
Length : max. 1750 mm

Material

Sight tube : PVC transparent
connection : PVC-Verschraubung mit PTFE-Stangenführung
Guide rod : Edelstahl, Titan, Hastelloy B, Hastelloy C oder PVCRohr
float : PE / PP

EK-CAN

PC program for CANopen sensors

Evaluation and configuration software for Fluid.iO CANopen sensors

Properties

Operating system : Windows
ltdata.BuildVersion : 1.0.5 (28.10.2025)
installation type : ZIP, portable
ltdata.Sprache : DE | EN

ELH

Suspension electrode as leakage probe

The leakage probes of the type series ELH are approved by the "DIBt" for the monitoring of collecting chambers, collecting devices, inspection and filling shafts.

General data

Protection class : IP 68
Probe body material : PE, PVC, PPH, PVDF
Diameter probe body : 15 mm, 25 mm, 40 mm
Operating temperature : atmosphärisch
Operating pressure : atmosphärisch
Resistance value of line monitoring : 22 kΩ / 100 kΩ

Material

Screw connection : PVDF
Cable : TPK ( PVC Basis)
on request : FEP (Teflon), PVC - blau
cable length : auf Wunsch (Standard 3 m)
Material Sensor rods : Edelstahl (1.4571), Hastelloy B, Hastelloy C, Titan, Tantal, Glas-Kohlestifte

Our application engineers advise you personally, comprehensively and professionally!

Simply contact us by phone or e-mail!

Call us right away!

+49-6251-8462-0

contact form