Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

8 article(s) in your cart
pos.	image	product	Configure	Actions
1		TK-101 EX
2		T205-0.F
3		QFS-40
4		ZT Serie
5		EFV2 20…230V
6		T204
7		T201
8		NP-25X

TK-101 EX configure

1 ATEX

Amount

additional infomation

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

EFV2 20…230V configure

1 Verschraubungsmaterial

2 Stabmaterial

3 Anschluss

4 Anschlussgewinde

5 Elektronikteil

6 Standaufnehmerlänge

Amount

additional infomation

NP-25X configure

1 Staurohrmaterial

2 Anschlussgewinde

3 Druckschaltermembran

4 Kontakt

5 Staurohrlänge

Amount

additional infomation

TK-101 EX

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

T205-0.F

Ex area zone 0 (category 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties

Protection class : IP 68 Kabel
connection cable : max. 10 Meter PUR
Sliding tube length : Max. 6000 mm
Operating temperature : max. 120 °C
F-Contact : 1 / 12 kΩ

Float

Stainless steel ball 44 mm Ø : max. 15 bar | 0,60 g/cm³
Stainless steel cylinder 27 mm Ø : max. 10 bar | 0,78 g/cm³

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

ZT Serie

Reliable pressure measurement and optimum process monitoring with the ZT series

From low to high pressure and suitable for liquid and gaseous media.

Properties

Pressure type : Relativdruck | Absolutdruck
Housing : Edelstahl
Overpressure : 1,5* fach bis 400 bar, darüber 1,2* fach
Bursting pressure : 3* fach bis 600 bar, darüber 1,5* fach

Measurement parameters

response time : < 1 ms
Total error : ≤ 0,5 % FS
Non-linearity : ≤ 0,2 % FS
Non-repeatability : ≤ 0,10 % FS
Hysteresis : ≤ 0,15 % FS

ambient conditions

Temperature of the fluid : -40...+125 °C (0...+80 °C kompensierter Bereich)
Ambient temperature : -40...+105 °C
Storage temperature : -40...+125°C
Shock resistance : g 1000 gemäß IEC 60068-2-32
Vibration resistance : g 20 gemäß IEC 60068-2-6

EFV2 20…230V

Conductive electrodes with 24...230 V direct connection

The overfill protection EFV2 (24...230 V AC/DC) is approved by the "DIBt" as overfill protection for liquids hazardous to water.

Properties

connection : Polyesterdose (PO)
Protection class : IP 65
connection thread : G2"
Union nut : G2¾" | S 100x8
Material Screw connection : PE, PVC, PPH, PVDF
Material Sensor rods : Edelstahl (1.4571), Hastelloy B, Hastelloy C, Titan, Tantal, Kohlestifte
Operating pressure : atmosphärisch
Resistance value of line monitoring : 100 kΩ
Adjustable sensitivity range : 2..100 kΩ

Operating temperature

PE : atmosphärisch
PVC : atmosphärisch
PPH : 90 °C
PVDF : 100 °C

Power supply

nominal voltage : 24...230 V AC/DC
Power consumption : ≤ 2 W

Output

potential-free changeover contacts : 2
Switching voltage : max. 250 V AC / 30 V DC
Switching current : max. 5 A AC / 5 A DC
Switching capacity : max. 750 VA / 90 W
displays : Betriebs- LED grün Funktions-LED rot
Switching delay : ca. 0,5 s

T204

Magnetic immersion probe made of stainless steel (1.4571)

For use with highly aggressive liquid media to detect level limit values in containers. Suitable for use in hazardous areas, zone 0 (category 1).

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
connection thread : G1 1/2" | G2"
Sliding tube length : max. 6000 mm (Rohr Ø 12 mm)
Operating pressure : max. 20 bar (Kugel) | max. 15 bar (Zylinder)
Operating temperature : max. 135 °C
Number of floats : max. 4

Float type

Stainless steel ball 52mm ⌀ : Dichte: 0,75 g/cm³ | mind. Kontaktabstand: 75 mm
Stainless steel ball 62mm ⌀ : Dichte: 0,65 g/cm³ | mind. Kontaktabstand: 85 mm
Stainless steel cylinder 44 mm Ø : Dichte: 0,76 g/cm³ | mind. Kontaktabstand: 75 mm

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 4
normally open : 6
Normally closed contact : 4

T201

Immersible Magnetic Probe made of stainless steel (1.4571)

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil