Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

10 article(s) in your cart
pos.	image	product	Configure	Actions
1		T200.F
2		XR Relais
3		T205 PP
4		XR-4x2
5		Aero_aH100
6		BK-3X0
7		ÜTA-32
8		KST-20 VENTO CO2
9		ZDS-N
10		NP-25X

XR-4x2 configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Empfindlichkeitsbereich

7 Versorgungsspannung

8 Busanschluss

9 SIL

10 ATEX

Amount

additional infomation

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

NP-25X configure

1 Staurohrmaterial

2 Anschlussgewinde

3 Druckschaltermembran

4 Kontakt

5 Staurohrlänge

Amount

additional infomation

T200.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

ltdata.Polyesterdose :
ltdata.Aluminiumdose :
ltdata.Polyethylenanschlusskopf :
Cable :
Plug :

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating pressure : Max. 20 bar
media density : ρ ≥ 0,6 g/cm³
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm
Operating temperature : atmosphärisch
ltdata.BetriebstemperaturPP : max. 90°C

Resistance value

Operational readiness : ca. 1 kΩ
overfill alarm : ca. 12 kΩ
Switching time : ca. 20 ms
ltdata. :

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529

clamp : IP20
Housing : IP40

Technical Data

Operating temperature : -20...+60 °C
Storage temperature : -30...+80 °C
Output contacts : potentialfrei
Switching voltage : min. 5 V | max. 250 V AC / 150 V DC
Switching current : min. 5 mA | max. 5 A AC / 5 A DC
Switching capacity : min. 300 mW | max. 100 VA / 50 W
Quiescent current : umschaltbar
Weight : ca. 250 g
CE marking : siehe Konformitätserklärung
Ex-protection/IECEx : siehe Prüfbescheinigung

T205 PP

Magnetic immersion probes made of PP

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

Protection class : IP 65
Number of floats : 1x Typ 12 | 1x Typ 13
connection cable : LiYY-Kabel 0,14 mm² | PVC-Litze 0,24 mm²
Operating temperature : max. 60 °C
Operating pressure : drucklos
Number of contacts : 1x Schließer / Öffner
Switching current : 1 A
Switching voltage : 250 V AC
Switching capacity : 50 W/VA

Float type

Type 12 : Zylinder PP 19 mm Ø | Dichte 0,93 g/cm³
Type 13 : Zylinder PP 25 mm Ø | 0,68 g/cm³

XR-4x2

Electrode relay with ATEX and WHG approval

Protection class EN60529

clamp : IP20
Housing : IP40

Technical Data

Operating temperature : -20...+60 °C
Storage temperature : -30...+80 °C
Output contacts : potentialfrei
Switching voltage : min. 5 V, max. 250 V AC / 150 V DC
Switching current : min. 5 mA, max. 5 A AC / 5 A DC
Switching capacity : min. 300 mW, max.100 VA / max. 50 W
CE marking : siehe Konformitätserklärung
Ex-protection/IECEx : siehe Baumusterprüfbescheinigung
Weight : ca. 170 g

Aero_aH100

Exhaust air fan with integrated dehumidification control for automatic room dehumidification

Dehumidification control, including integrated indoor and outdoor climate sensor. Controlled dehumidification takes place by comparing the indoor and outdoor climate. To support room dehumidification, a ventilation fan can be directly connected and controlled via the Aero_aH 100.

Properties

Power supply : 230V~ 50Hz
power consumption : 8 W
Protection class : IPX4
flow rate : 78 m³/h bis zu 92 m³/h
color : verkehrsweiß, ähnlich RAL 9016
Material : Kunststoff
Noise level : 27 dB(A) / 32 dB(A)
Signal output : I²C

Measuring range

measuring range (Humidity) : 0…100% rF
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -40...+80°C
Measuring accuracy (temperature) : ± 0,2°C

BK-3X0

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties

connection : G 1” (andere Gewinde auf Anfrage)
max.length guide tube : siehe Diagramm
Operating temperature : atmosphär. Bedingungen
Operating pressure : atmosphär. Bedingungen
media density : siehe Eintauchtiefe
Number of contacts : beliebig
Contact load : max. 10 VA, max. 230 V AC
Length : max. 1750 mm

Material

Sight tube : PVC transparent
connection : PVC-Verschraubung mit PTFE-Stangenführung
Guide rod : Edelstahl, Titan, Hastelloy B, Hastelloy C oder PVCRohr
float : PE / PP

KST-20 VENTO CO2

KST-20 Vento with air quality monitoring function

Automatic, controlled ventilation and dehumidification of rooms with the aH-Controlled technology*

Properties

measuring range (Humidity) : 0…100 % rF,
Measuring accuracy (humidity) : ±2 %
measuring range (Temperature) : -40…+80 °C
Measuring accuracy (temperature) : ±0,2 °C
Signal output : I2C
measuring range (CO2) : 0…5.000 ppm
Adjustable limits : 1.000…1.500 ppm
Power supply : 230 V AC
Protection class : IP 65
Dimensions (LxBxH) : 160 x 90 x 50 mm
Housing : hochwertiges ASA+PC (UL 94 V-0) für harte Beanspruchung, flammwidrig und selbstverlöschend