Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

4 article(s) in your cart
pos.	image	product	Configure	Actions
1		ÜTA-32
2		T208
3		T-200.L Ex
4		T203.F

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

T-200.L Ex configure

1 Länge

2 Anschluss

3 Anschlussgewinde

4 Schwimmertyp

5 Ex

Amount

additional infomation

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties

connection : G 1” (andere Gewinde auf Anfrage)
max.length guide tube : siehe Diagramm
Operating temperature : atmosphär. Bedingungen
Operating pressure : atmosphär. Bedingungen
media density : siehe Eintauchtiefe
Number of contacts : beliebig
Contact load : max. 10 VA, max. 230 V AC
Length : max. 1750 mm

Material

Sight tube : PVC transparent
connection : PVC-Verschraubung mit PTFE-Stangenführung
Guide rod : Edelstahl, Titan, Hastelloy B, Hastelloy C oder PVCRohr
float : PE / PP

T208

Immersible Magnetic Probe made of PVC, PE, PPH

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil

Operating temperature

ltdata. : max. +60...+150 °C
ltdata. : min. –20... –10 °C
ltdata. : höhere oder niedrigere Temperaturen auf Anfrage

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 8
normally open : 10
Normally closed contact : 7

T-200.L Ex

Leakage probes with general building authority approval for hazardous areas

The leakage probes T-200.L are approved by the "DIBt" on the basis of the "WasBauPVO" for the detection of leaking water-polluting liquids. The T-200.L Ex may be used as leakage probes in hazardous areas, zone 1 (category 2).

Connection

Box : Ex-Polyesterdose (PO)

Properties

Protection class : IP 65
Cable entry : PVDF-Verschraubung, PVC-Dichtung
Material Float : PE
Material leakage probe base : PE
Cable : TPK (PVC Basis)
Operating temperature : atmosphärisch
Operating pressure : atmosphärisch
media density : mit Schwimmer PE 52 ρ ≥ 1,05 g/cm³
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Resistance value

Operational readiness : ca. 1 kΩ
Leakage detection : ca. 12 kΩ
Switching time : ca. 20 ms

T203.F

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Properties