Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

10 article(s) in your cart
pos.	image	product	Configure	Actions
1		T204.F
2		T-200.F Ex
3		T209-0.F
4		TK-101 EX
5		QFS-40
6		T205-0.F
7		KST-20 VENTO CO2
8		T-200.L
9		T209
10		T209-0

T-200.F Ex configure

1 Führungsrohr

2 Sicherheitsfunktion

3 Rohrmaterial

4 Anschlussgewinde

5 Ausführung

6 Schaltkontakte

7 Schwimmermaterial

8 Anschlussdose

9 Länge

10 EX

Amount

additional infomation

TK-101 EX configure

1 ATEX

Amount

additional infomation

QFS-40 configure

1 Anschluss

2 Gehäusematerial

3 Kabelmaterial

4 Kabellänge

Amount

additional infomation

T-200.L configure

1 Länge

2 Anschluss

3 Anschlussgewinde

4 Befestigungswinkel

5 Schwimmertyp

Amount

additional infomation

T204.F

Immersible Magnetic Probes Ex area zone 0 (Cat 1)

Properties

connection : Polyester Dose | Aluminium Dose
Protection class : IP 65 Dose
number of floats : max. 4x
Operating temperature : max. 135 °C
F-Contact : 1 / 12 kΩ
Number of additional contacts : max. 3x Wechsler | 5x Schließer | 3x Öffner
Switching current : 1 A, 2 A (nur mit Schirmung)
Switching voltage : 230 V AC

Float

Stainless steel ball 52mm Ø : max. 20 bar | 0,75 g/cm³
Stainless steel ball 61 mm Ø : max. 20 bar | 0,65 g/cm³
Stainless steel cylinder 44 mm Ø : max. 15 bar | 0,76 g/cm³
min. contact gap type 03 : 75 mm
min. contact gap type 04 : 85 mm
min. contact gap type 09 : 75 mm

Switching contacts and switching capacity

Changeover contact : max. 3x | 60W/VA
normally open : max. 5x | 100 W / VA
Normally closed contact : max. 3x | 60 W/VA

T-200.F Ex

Overfill protection for containers with Ex approval

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

Box : Ex-Polyester
Box : Ex-Aluminium

Properties

Protection class EN60529 : IP 65
connection thread : G2"
Union nut : G 2¾"
Guide tube length : max. 6 m
Operating temperature : -20…+60 °C
Operating pressure : max. 6 bar je nach Ausführung
media density : ρ ≥ 0,72 g/cm³ (je nach Schwimmertyp)
Switching hysteresis : 2 mm
Switching point tolerance : max. 2 mm

Resistance value

Operational readiness : ca. 1 kΩ
overfill alarm : ca. 12 kΩ
Switching time : ca. 20 ms
Ex-protection : siehe Baumusterprüfbescheinigung
CE marking : siehe Konformitätserklärung

T209-0.F

Magnetic immersion probe overfill protection for Ex zone 0 (Cat. 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties

connection : Polyesterdose, Aluminiumdose
Protection class : IP 65 Dose
Float type : Kugel Edelstahl 105 mm Ø
Sliding tube length : max. 6000 mm
Operating temperature : max. 135°C
Operating pressure : max. 20 bar
media density : 0,54 g/cm³
F-Contact : 1 / 12 kΩ
Number of additional contacts : 6x Wechsler, 9x Schließer, 6x Öffner
Switching current : 1A, 2A ( nur mit Schirmung)
Switching capacity : Wechsler: 60 W/VA, Schließer: 100 W/VA Öffner: 60 W/VA
min. contact distance with several floats : 125 mm

TK-101 EX

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

QFS-40

Built-in float level switch

The QFS-40 built-in float switch is designed for low-cost monitoring of liquids in containers.

Technical Data

Switch housing : PPH| PVDF
Seal : NBR (PPH) | FPM (PVDF)
Operating temperature : PPH max. 80 °C| PVDF max. 100 °C
Operating pressure : max. 10 bar
Mounting position : horizontal (±30° von der Horizontalen)
Contact assembly : Schliesser-, Öffnerkontakt (je nach Einbau)
Electrical connection : PVC-Kabel
Switching capacity : max. 230 V AC/DC| max. 40 VA, max. 2 A
Contact resistance : max. 80 mW
Min. electric strength : 400 V DC / 1 s
Inductive/capacitive loads : Unbedingt Kontaktschutz vorsehen
fluid density : PPH > 0,6 kg/dm³ | PVDF > 0,95 kg/dm³
Protection class : IP 68

Connections

external installation : G ½"
internal installation : M16

T205-0.F

Ex area zone 0 (category 1)

Properties

Protection class EN60529 cable : IP 68
connection cable : max. 10 Meter PUR
Sliding tube length : Max. 6000 mm
Operating temperature : max. 120 °C
F-Contact : 1 / 12 kΩ

Float

Stainless steel ball 44 mm Ø : max. 15 bar | 0,60 g/cm³
Stainless steel cylinder 27 mm Ø : max. 10 bar | 0,78 g/cm³

KST-20 VENTO CO2

KST-20 Vento with air quality monitoring function

Automatic, controlled ventilation and dehumidification of rooms with the aH-Controlled technology*

Properties

measuring range (Humidity) : 0…100 % rF,
Measuring accuracy (humidity) : ±2 %
measuring range (Temperature) : -40…+80 °C
Measuring accuracy (temperature) : ±0,2 °C
Signal output : I2C
measuring range (CO2) : 0…5.000 ppm
Adjustable limits : 1.000…1.500 ppm
Power supply : 230 V AC
Protection class : IP 65
Dimensions (LxBxH) : 160 x 90 x 50 mm
Housing : hochwertiges ASA+PC (UL 94 V-0) für harte Beanspruchung, flammwidrig und selbstverlöschend

Measuring range

measuring range (Humidity) : 0...100 % rF
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -40...+80 °C
Measuring accuracy (temperature) : ± 0,2 °C
measuring range (CO2) : 0…5.000 ppm
Adjustable limits : 1.000...1.500 ppm

T-200.L

Leakage probes with general building authority approval

The leakage probes T-200.L are approved by the "DIBt" on the basis of the "WasBauPVO" for the detection of leaked liquids hazardous to water.

Connection

Box : Polyesterdose (PO)
Box : Polyethylen-Anschlusskopf (PE)
Cable : Kabel (TPK)
Plug : Stecker (ST)

Properties

Protection class : IP 65
Cable entry : PVDF-Verschraubung , PVC-Dichtung
Material Float : PE
Material leakage probe base : PE
Cable : TPK (PVC Basis)
Operating temperature : atmosphärisch
Operating pressure : atmosphärisch
media density : mit Schwimmer PE 52 ρ ≥ 1,05 g/cm³
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Resistance value

Operational readiness : ca. 1 kΩ
Leakage detection : ca. 12 kΩ

T209

Immersible Magnetic Probe made of PVC, PE, PPH, PTFE or stainless steel (1.4571)

Magnetic immersion probes for use with highly aggressive liquid media for detecting level limits in containers

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil