Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

10 article(s) in your cart
pos.	image	product	Configure	Actions
1		XR Relais
2		TPS-410 TPS-420
3		QFS-2X
4		BK-3X0
5		BK-380
6		ZMF-100-IR
7		TK-313
8		MTA
9		TRM-100
10		ÜTA-32

XR Relais configure

1 Kanalanzahl

2 WHG

3 Gehäuse

4 Ausgang

5 Schaltverzögerung

6 Versorgungsspannung

7 Busanschluss

8 SIL

9 ATEX

Amount

additional infomation

QFS-2X configure

1 Schwimmertyp

2 Kontakt

3 Kabelmaterial

4 Kabellänge

5 EX

Amount

additional infomation

BK-380 configure

1 Kontakt

2 Stecker

Amount

additional infomation

ZMF-100-IR configure

1 Output signal

2 Measuring range

Amount

additional infomation

TK-313 configure

1 Gehäuse

2 Eingang

Amount

additional infomation

MTA configure

1 Außendurchmesser

2 Seilsicherung

3 Seil

4 Schwimmer

Amount

additional infomation

TRM-100 configure

1 Material

2 Measuringrange

3 Connection

4 Flange

5 Sealing

Amount

additional infomation

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

XR Relais

Electrode relays and contact protection relays

The electrode relays are used for conductive level detection. levels. The possible applications extend areas where conductive, liquid media are to be detected, controlled to be detected, controlled or regulated. Hereby level detection (overflow / dry run) as well as minimum / maximum as well as minimum / maximum controls can be realised. The contact protection relays are universal measuring transducers, which input signals (resistance values) with "Namur" specification (DIN EN 60947). Namur" specification (DIN EN 60947) into switching signals of floating output contacts.

Protection class EN60529

clamp : IP20
Housing : IP40

Technical Data

Operating temperature : -20...+60 °C
Storage temperature : -30...+80 °C
Output contacts : potentialfrei
Switching voltage : min. 5 V | max. 250 V AC / 150 V DC
Switching current : min. 5 mA | max. 5 A AC / 5 A DC
Switching capacity : min. 300 mW | max. 100 VA / 50 W
Weight : ca. 170g
CE marking : siehe Konformitätserklärung
Ex-protection/IECEx : siehe Prüfbescheinigung

TPS-410 TPS-420

Compact, analogue dew point sensor

The dew point sensors of the enable direct measurement of the dew point and ambient temperature indoors and outdoors.

Properties TPS-410

Operating voltage : 12...30V DC
Power consumption : < 15mA
Protection class : Gehäuse IP66, Stecker IP 67
Weight : 96g

Properties TPS-420

Operating voltage : 24V DC
Loop voltage min: : Bürde(Ohm) *0,02 + 8 V
Loop voltage max: : 30V

General properties

Housing : Aluminium, eloxiert
Dimensions (in mm) : 135 x Ø 19,2

Measuring range

measuring range (dew point) : -50…+80 °C
Measuring accuracy (humidity) : ± 2%
measuring range (Temperature) : -40...+80°C
Measuring accuracy (temperature) : ± 0,2°C
Signal output : 0...10V | 4...20mA

QFS-2X

Stainless Steel Float Switch

QFS-20 & QFS-21 float switches have stainless steel floats and one or two reed contacts.

Properties

Protection class EN60529 : IP68
Material Float : VA 1.4571
Material hose : Edelstahlwellschlauch (1.4404) mit Edelstahldrahtumflechtung (1.4301)
Operating temperature : max. + 150 °C
media density : ρ ≥ 0,8g/cm³
Switching system : Reed-Schalter
Contact : Wechsler, NO, NC
Switching voltage : 4...250 V AC/DC
Switching current : 1 mA ...1 A
Switching capacity : max. 1A, 60 VA/60 W
Switching hysteresis : ca. 100 mm
Switching angle : ca. + 20° / – 20°
Operating pressure (QFS-20) : max. 15 bar
Operating pressure (QFS-21) : max. 6 bar

BK-3X0

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

BK-380

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

ZMF-100-IR

gas detector with 4...20mA signal output

industrial CO2 sensor ZMF-100-IR with a measuring range of up to 50,000ppm

Product features

Measuring principle : optisch, NDIR (nicht-dispersive Infrarot-Absorptionsmessung)
Operating voltage : 24 V DC / 100 mA
Heating time : ca. 5 min
Response time : ca. 30 s
Repeatability : +/- 1%
Housing : Aluminium (rot) IP54
Weight : ca. 500g
Shaft range : 4,27 - 4,35 µm (4270-4350 nm)
Gas ingress : per Diffusion

ambient conditions

Operating temperature range : -10...+50 °C
Storage temperature range : -40...+100 °C
RelativeHumidity : 15..95 %
Air pressure : 900...1100 hPa

TK-313

Evaluation unit with 2 change over limit contacts

The TK-313 limit comparator can be used in conjunction with our TK-30... continuous level sensors with 0(4)...20 mA or 0...10 V output signal for level control / measurement.

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
nominal voltage : 24... 230 V AC/DC
Power consumption : 2 VA
Dimensions housing type B : 22,5 x 114,5 x 99
Dimensions housing type C : 22,5 x 114,5 x 114

Input

power : 0/4...20 mA
Voltage : 0...10 V
Resistance in three-wire circuit RG : 0–4...10 kΩ

Output

Output contacts : 2 Wechselkontakte
Switching voltage : max. 250 V AC
Switching current : max. 3 A
Switching capacity : max. 500 VA
Temperature influence tolerance : max. ± 0,6 % der Signalspanne
Mounting : Tragschiene nach EN 50022
Current output : 4...20 mA bezogen auf die Masse des Eingangs
Display (%) : 2-stellig, 7-Segment
Weight : 175 g
ltdata. :

MTA

Mechanical tank level indicator

The tank level indicator is a mechanically actuated indication operating "on the spot”. It permits a high degree of safety and flexibility thanks to separate points of measurement and indication.

Properties

Tank connection : Flansch ab DN 80 (Sonderanschlüsse auf Wunsch)
Material : siehe Maßbild
Material Tube : PVC, transparent | Ø 50 x 1,8 | Ø 63 x 3,0
Operating temperature : –20...+60 °C
Operating pressure : atmosphärisch

Material Float

PPH : Ø 70 mm 460 g
PVC : Ø 70 mm 455 g
PPH : Ø 40 mm 370g
PE : Ø 70 mm ca. 450 g

Material Rope

PPH : (rot, Ø 2 mm) ~ 2 g/m
Polyester : (bunt, Ø 2 mm) ~ 4 g/m
PTFE : (weiss, Ø 3 mm) ~ 10 g/m

TRM-100

Turbidimeter (0...1.000 FNU or 500...4.000 FAU)

The turbidimeter TRM-100 is a compact device for measuring turbidity in liquids. The "turbidity" is measured using the scattered light method (angle 90 degrees) for the turbidity range of < 1,000 FNU (Formazine Nephelometric Units) and the transmitted light method (angle 0 degrees) for the turbidity ranges > 1,000 FAU (Formazine Attenuation Units).

Properties

Operating pressure : max. 10 bar @ 20 °C | max. 2,5 bar @ 60 °C
Measuring range : 500...4.000 FNU / FAU
Measuring accuracy : +/-5 %
Mounting position : horizontal
Process connection : DN 20 | DN 40
Flange connection : >= DN 20
number of senders : 2
number of receivers : 1

Material

Seal : EPDM | optional FPM (Viton)
Process connection : PVC | PPH
Measuring tube : Borsilikatglas mit Nano Beschichtung

Input

Power supply : 18...30 V DC
Power consumption : < 2 W

Output

Output contact : 4...20 mA
Switching delay (adjustable) : 1...10 s
Protection class : IP 65
Switching voltage : max. 250 V AC | max. 115 V DC
Switching current : max. 3 A
Switching capacity : max. 500 VA, 60 Watt
Potential-free changeover contact : 1 @ 1...10 s

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties