Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

6 article(s) in your cart
pos.	image	product	Configure	Actions
1		TK-30X
2		T200.F-24V
3		TK-101 EX
4		ÜTA-32
5		TK-101
6		ZDS-H

TK-30X configure

1 Rohrdurchmesser

2 Rohrmaterial

3 Gewinde

4 Ausführung

5 Schwimmerausführung

6 Anschluss

7 Rohrlänge

8 Auflösung

9 Zubehör

Amount

additional infomation

T200.F-24V configure

1 Führungsrohr

2 Sicherheitsfunktion

3 Rohrmaterial

4 Anschlussgewinde

5 Ausführung

6 Schwimmermaterial

7 Anschluss-Elektronikteil

Amount

additional infomation

TK-101 EX configure

1 ATEX

Amount

additional infomation

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

TK-101 configure

1 ATEX

Amount

additional infomation

TK-30X

Liquid Level Measuring Instruments Series

T30... continuous magnetic immersible probes are used for quasi-acquisition of the filling level in containers with liquid media.

Properties

connection : Polyesterdose | Aluminiumdose | Stecker nach DIN 43650
connection thread : G 3/8”, G 1/2”, G 1”, G 1 1/2”, G 2”, G 3”
connection cable : LiYY max. 80 °C | Silikon max. 130 °C
Sliding tube length : max. 6000 mm
Operating temperature : max. +60...+130 °C | min. –20...–10 °C je nach Ausführung
Operating pressure : max. 20 bar je nach Ausführung
media density : siehe Schwimmerdaten
Viscosity : < 100 cp
Switching hysteresis : ca. halbe Auflösung
Resolution : 7,5 mm, 10 mm, 15 mm, 20 mm oder 1 %, 2 %, 5 % je nach Ausführung
Total resistance : ca. 5 kΩ
Measuring voltage : max. 24 V
Measuring current : max. 5 mA

T200.F-24V

Overfill protection with 24V direct connection

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

ltdata.Polyesterdose : PO/ET-520
ltdata.Polyethylenanschlusskopf : PE/ET-521

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating temperature : max. 80 °C
Operating pressure : atmosphärisch
media density : ρ ≥ 0,6 g/cm³ (je nach Schwimmertyp)
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Power supply

nominal voltage : 24 V DC (24…300V DC)
Power consumption : ≤ 1 W

Output

Output contact : 1 potentialfreier Wechselkontakt
Switching voltage : max. 250 V AC / 30 V DC
Switching current : max. 3 A AC / 3 A DC
Switching capacity : max. 750 VA / 90 W

Optocoupler

Switching voltage : max. 30 V
Switching current : max. 100 mA
displays : Betriebs-LED grün, Funktions-LED rot
Switching delay : ca. 0,5 s Anzug/Abfall

TK-101 EX

Measuring transducer (R/I-transducer)

The measuring transducer Tk101 and Tk101Ex are built directly into the connection boxes of our Liquid Level Measuring Instruments of type TK-30.

Properties

Operating temperature : -20...+60 °C
Storage temperature : -40...+80 °C
Ex-protection : siehe Zertifikat
CE marking : siehe Konformitätserklärung

Input

Resistance range in three-wire circuit : 4...10 kΩ
Measuring current : 0,8 mA @ RE = 4 kΩ
Measuring current : 0,33 mA bei RE = 10 kΩ
Measuring voltage : 3,3 V

Supply/Output

2-wire : 4...20 mA
Voltage(Um) : 11...28 V DC
Burden / load : 0...800 Ω |RBürde max = [(Um - Um min) / 0,02] Ω
Output signal in case of error : max. 24 mA

Fault influences

Max. Total error : ± 1 %
Temperature influence : -0,015 % / °C
Supply voltage influence : 0,025 % / V

Setting range

Full deflection : 60...105 %
Zero point adjustment : 0...25 %

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties