Home
Cart

Cart

product added to request

Get an offer

Full name*

E-Mail*

telephone*

Company*

street*

place*

zip code*

country*

additional information

I agree that my details and data are collected and stored electronically in order to answer my enquiry.

Your cart

11 article(s) in your cart
pos.	image	product	Configure	Actions
1		DS-CAN-01
2		T200 Ex
3		ZDS-N
4		T209-0.F
5		ZT Serie
6		BK-390
7		ER-104
8		T-20x.F 230V
9		CSC-20 YUGO
10		ÜTA-32
11		AD-310

BK-390 configure

1 Rohr-Außendurchmesser

2 Kontakt

3 Stecker

Amount

additional infomation

T-20x.F 230V configure

1 Führungsrohr

2 Sicherheitsfunktion

3 Rohrmaterial

4 Anschlussgewinde

5 Ausführung

6 Schwimmermaterial

7 Anschluss-Elektronikteil

8 Länge

Amount

additional infomation

ÜTA-32 configure

1 Float

2 Guide-rod

3 Length

Amount

additional infomation

AD-310 configure

1 Grenzkontakte

2 Versorgungsspannung

3 Schnittstelle

Amount

additional infomation

DS-CAN-01

CANopen pressure transmitter with CAN bus signal output

Versatile, media-compatible pressure transmitter with CAN bus interface.

technical properties

Pressure type : Relativdruck gegen Umgebungsdruck bzw. gegen interne Atmosphäre
measuring resolution : 10 Bit
Measuring accuracy : Klasse 0,5 bei RT
Total error : < 1,5 % v.E bei -10 °C … +80 °C.
measuring grid : ab 5 ms
CAN protocol : CANopen 2.0 A
Physical Layer : nach DIN 11898

ambient conditions

Operating temperature range : -40 °C … +80 °C
Storage temperature range : -40 °C … +120 °C
Shock resistance : 30 g, Dauer
Vibration resistance : 10 g bei 20-1000 Hz
EMC/ESD : EN 50082-1 und EN 50082-2
Duration : 14 ms bei RT

Pressure measuring ranges

kPa : bar
0...500 : 0…5
0...1.000 : 0…10
0...2.000 : 0…20
0...5.000 : 0…50
0...10.000 : 0…100
0...35.000 : 0…350
0...50.000 : 0…500
0...70.000 : 0…700
0...200.000 : 0…2.000
0...400.000 : 0…4.000
Standard pressure range : in kPa
Non-standard ranges : auf Anfrage erhältlich

T200 Ex

Magnetic immersion probes with TÜV 02 ATEX 1795X approval for Ex zone 0

Magnetic immersion probes for detecting fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (category 1) is present in the gas space above the liquid and zone 1 (category 2) outside the container in the area of the junction box

Properties

connection : Polyesterdose | Aluminiumdose
Protection class EN60529 : IP 65 Anschlussdose
Connector plug : 3- und 6-fach
connection thread : G 1/8" | G 3/8" | G 1/4" | G 1/2" | G 1" | G1 1/4" | G1 1/2" | G2" | G3"
connection cable : LiYY max. 80 °C | PTFE-Litze, 0,24 mm² | Silikon max. 150 °C
Sliding tube length : max. 1000 mm (Rohr Ø 8 mm) | 6000 mm
Operating pressure : max. 20 bar
Viscosity : < 100 cp
Protection class EN60529 : IP 68 Führungsrohr
Switching voltage : max. 250 V
Switching hysteresis : ca. 2...5 mm
Holding range : ca. 12 mm
Contact function : monostabil | bistabil

Operating temperature

ltdata. : max. +60...+150 °C
ltdata. : min. –20... –10 °C
ltdata. : höhere oder niedrigere Temperaturen auf Anfrage

Switching capacity

Changeover contact : 60 W/VA
normally open : 100 W/VA
Normally closed contact : 60 W/VA

Switching current

Changeover contact : max. 1 A
NO/NC contact : max. 2 A

Contacts

Changeover contact : 8
normally open : 10
Normally closed contact : 7

ZDS-N

Precision pressure switch for low pressure applications

Can be used in oil, brake fluid, diesel, air and other gases. With very good stability and overpressure resistance.

technical properties

Pressure range : 0...500mbar gestuft
supply : 12 - 24 V DC
Output : Relais 230 V/1A
overload : 2 x Messbereich
Med. connection : Schlauch
electrical connection : Schraubklemme
feature : Tasten, LCD-Anz.

T209-0.F

Magnetic immersion probe overfill protection for Ex zone 0 (Cat. 1)

The magnetic immersion probes T20... are used to detect fill level limit values in containers for liquid media, where an explosive atmosphere of zone 0 (cat. 1) is present in the gas space above the liquid and Ex zone 1 (cat. 2) is present outside the container, in the area of the junction box.

Properties

connection : Polyesterdose, Aluminiumdose
Protection class : IP 65 Dose
Float type : Kugel Edelstahl 105 mm Ø
Sliding tube length : max. 6000 mm
Operating temperature : max. 135°C
Operating pressure : max. 20 bar
media density : 0,54 g/cm³
F-Contact : 1 / 12 kΩ
Number of additional contacts : 6x Wechsler, 9x Schließer, 6x Öffner
Switching current : 1A, 2A ( nur mit Schirmung)
Switching capacity : Wechsler: 60 W/VA, Schließer: 100 W/VA Öffner: 60 W/VA
min. contact distance with several floats : 125 mm

ZT Serie

Reliable pressure measurement and optimum process monitoring with the ZT series

From low to high pressure and suitable for liquid and gaseous media.

Properties

Pressure type : Relativdruck | Absolutdruck
Housing : Edelstahl
Overpressure : 1,5* fach bis 400 bar, darüber 1,2* fach
Bursting pressure : 3* fach bis 600 bar, darüber 1,5* fach

Measurement parameters

response time : < 1 ms
Total error : ≤ 0,5 % FS
Non-linearity : ≤ 0,2 % FS
Non-repeatability : ≤ 0,10 % FS
Hysteresis : ≤ 0,15 % FS

ambient conditions

Temperature of the fluid : -40...+125 °C (0...+80 °C kompensierter Bereich)
Ambient temperature : -40...+105 °C
Storage temperature : -40...+125°C
Shock resistance : g 1000 gemäß IEC 60068-2-32
Vibration resistance : g 20 gemäß IEC 60068-2-6

BK-390

Bistable change-over contact

Magnetically actuated changeover switch, which permanently changes its electrical switching state as a result of a magnetic system passing by, depending on the direction of movement.

Properties

Protection class EN60529 : IP 65
Operating temperature : –25...+70 °C
Wire cross-section max. : 1,5mm²
Switching point distance between two contacts : min. 40 mm
Switching hysteresis : ca. 10-15 mm

Material

Housing : Polycarbonat
Mounting clip : V2A, Kabelbinder (PP)
Rivet : V2A
Screw connection : M 20 x 1.5, Polyamid

Weight

BK-390-50 : 137 g
BK-390-63 / BK-380 : 140 g

Switching contact

Switching voltage : 5...250 V AC/DC
Switching current : 1mA...6 A AC/DC
Switching capacity(min.) : 300 VA, 60 W
Switching capacity(max.) : 5 mW

ER-104

1-channel electrode relay

Electrode relays for conductive level detection for all areas in which conductive, liquid media are to be detected, controlled or monitored

Properties

Protection class EN60529 clamp : IP 20
Protection class EN60529 front panel housing : IP 40
Operating temperature : –20...+60 °C
Storage temperature : –30...+80 °C
Weight : ca. 150g
ltdata. :

Power supply

nominal voltage : siehe Typenschlüssel
AC nominal frequency : 48...62 Hz
Power consumption : max. 1 W / VA

Input

Open circuit voltage : ≤ 10 V AC
Short-circuit current : ≤ 5 mA
Switching delay : siehe Typenschlüssel
Sensitivity range : siehe Typenschlüssel

Output

Contacts : potentialfreie Wechselkontakte
Switching voltage(min) : 5 V
Switching voltage (max) : 250 V AC / 150 V DC
Overvoltage category : EN 61010-1 Kategorie III

Switching current

Switching current : min. 5 mA
Switching current : max. cos φ =1 5 A
Switching current : max. cos φ = 0,7 3 A/AC
Switching current : max. cos φ = 1

T-20x.F 230V

Overfill protection for containers

Level sensors type T-20_.F... are approved by the DIBt (German Institute for Structural Engineering) as liquid level limit switches for the overcharge protection of containers for storing water-dangerous liquids.

Connection

Box : Polyester

Properties

Protection class EN60529 : IP 65
connection thread : G 1", G 1¼", G 1½", G2", G3”
Union nut : G 2¾", S 100x8
Guide tube length : max. 6 m
Operating temperature : max. 80°C
Operating pressure : atmosphärisch
media density : ρ ≥ 0,6 g/cm³ (je nach Schwimmertyp)
Switching hysteresis : typ. 2 mm
Switching point tolerance : max. 2 mm

Power supply

nominal voltage : 24…230 V AC/DC
Power consumption : ≤ 2 W

Output

Output contact : 2 potentialfreie Wechselkontakte
Switching voltage : max. 250 V AC / 30 V DC
Switching current : max. 5 A AC / 5 A DC
Switching capacity : max. 750 VA / 90 W
displays : Betriebs-LED grün, Funktions-LED rot
Switching delay : ca. 0,5 s Anzug/Abfall
CE marking : siehe Konformitätserklärung

CSC-20 YUGO

Decentralised control unit, equipped with a CO2 sensor for needs-based ventilation

Decentralised CO2 monitoring with direct control of various supply and exhaust air elements such as fans and dampers (0..10.000 ppm)

Properties

Power supply : 230 V AC
measuring range (CO2) : 0..10.000 ppm
Measuring accuracy CO2 : ± 50ppm +3 % vom Messwert
Operating conditions : 0…50°C / 0…85 %rH
Storage conditions : -30…70°C / 0…85 %rH
Protection class : IP 31
EMV/ESD : EN 50082-1, EN 50082-2
Signal output : I²C

ÜTA-32

Overfuelling indicator

The top-mounted tank indicator is a mechanically operated, on-the-spot indicator. The liquid level in the tank located below the indicator is determined proportionately to the filling level and is indicated. Control of the level is easily achieved through the installation of switching contacts. The switching points for level control can be steplessly adjusted, on-the-spot and at any time.

Properties

connection : G 1” (andere Gewinde auf Anfrage)
max.length guide tube : siehe Diagramm
Operating temperature : atmosphär. Bedingungen
Operating pressure : atmosphär. Bedingungen
media density : siehe Eintauchtiefe
Number of contacts : beliebig
Contact load : max. 10 VA, max. 230 V AC
Length : max. 1750 mm

Material

Sight tube : PVC transparent
connection : PVC-Verschraubung mit PTFE-Stangenführung
Guide rod : Edelstahl, Titan, Hastelloy B, Hastelloy C oder PVCRohr
float : PE / PP

AD-310

programmable Digital Display

The programmable digital display AD-31… can be used in all applications through the parameterization capability of the input values and the display area.

Properties